background image

4

SERVICE

n

 

Tool service must be performed only by qualified 
repair personnel. 

Service or maintenance performed 

by unqualified personnel may result in a risk of injury.

n

 

When servicing a tool, use only identical replace-
ment parts. Follow instructions in the Maintenance 
section of this manual. 

Use of unauthorized parts or 

failure to follow Maintenance Instructions may create a 
risk of shock or injury.

n

Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden 
wiring. 

Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator.

ADDITIONAL RULES FOR SAFE OPERATION

n

Know your power tool. Read operator's manual care-
fully.  Learn  its  applications  and  limitations,  as  well 
as the specific potential hazards related to this tool. 

Following this rule will reduce the risk of electric shock, 
fire, or serious injury.

n

 

Always wear safety glasses with side shields. 

Everyday 

glasses have only impact resistant lenses. They are NOT 
safety glasses. Following this rule will reduce the risk of 
eye injury.

IMPORTANT RULES FOR BATTERY TOOLS

n

Battery tools do not have to be plugged into an elec-
trical outlet; therefore, they are always in operating 
condition.  Be  aware  of  possible  hazards  when  not 
using your battery tool or when changing accessories. 

Following this rule will reduce the risk of electric shock, 
fire, or serious personal injury.

n

 

Do not place battery tools or their batteries near fire 
or heat. 

This will reduce the risk of explosion and pos-

sibly injury.

n

  Batteries vent hydrogen gas and can explode in the pres-

ence of a source of ignition, such as a pilot light. To reduce 
the risk of serious personal injury, never use any cordless 
product in the presence of open flame. An exploded bat-
tery can propel debris and chemicals. If exposed, flush 
with water immediately. 

 

n

 

Do not charge battery tool in a damp or wet location. 

Following this rule will reduce the risk of electric shock.

n

 

For best results, your battery tool should be charged in 
a location where the temperature is more than 50°F but 
less than 100°F. Do not store outside or in vehicles.

n

 

Under extreme usage or temperature conditions, bat-
tery leakage may occur. If liquid comes in contact with 
your skin, wash immediately with soap and water, then 
neutralize with lemon juice or vinegar. If liquid gets 
into your eyes, flush them with clean water for at least 
10 minutes, then seek immediate medical attention. 

Following this rule will reduce the risk of serious personal 
injury.

GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

Содержание R84001





















Отзывы: