background image

0

Fig. 4

OPERATION

Fig. 5

SWITCH TRIGGER

See Figure 4.

To turn the screwdriver 

ON, depress the switch trigger. To 

turn it 

OFF, release the switch trigger.

VARIABLE SPEED

The variable speed switch trigger delivers higher speed with 
increased trigger pressure and lower speed with decreased 
trigger pressure.
NOTE:  You  might  hear  a  whistling  or  ringing  noise  from 
the  switch  during  use.  Do  not  be  concerned;  this  is  a  
normal part of the switch function.

DIRECTION OF ROTATION SELECTOR

See Figure 4.

The direction of bit rotation is reversible and is controlled 
by  a  selector  located  above  the  switch  trigger.  With  the 
screwdriver held in normal operating position, the direction 
of rotation selector should be positioned to the left of the 
switch trigger for driving. The driving direction is reversed 
when the selector is to the right of the switch trigger. 
Setting the switch trigger in the 

OFF (center lock) position 

helps reduce the possibility of accidental starting when not 
in use.

CAUTION:

 

To prevent gear damage, always allow the chuck 
to come to a complete stop before changing the 
direction of rotation. 

To stop the screwdriver, release the switch trigger and allow 
the chuck to come to a complete stop.
NOTE: The screwdriver will not run unless the direction of 
rotation selector is pushed fully to the left or right.
Avoid running the screwdriver at low speeds for extended 
periods  of  time.  Running  at  low  speeds  under  constant 
usage may cause the screwdriver to become overheated. 
If this occurs, cool the screwdriver by running it without a 
load and at full speed.

ADJUSTABLE TORQUE CLUTCH

This  product  is  equipped  with  an  adjustable  torque  
clutch  for  driving  different  types  of  screws  into  different 
materials.  The  proper  setting  depends  on  the  type  of 
material and the size of screw you are using.

TO DECREASE 

TORQUE

ADJUSTING 

RING

TO INCREASE 

TORQUE

SWITCH 

TRIGGER

FORWARD

REVERSE

DIRECTION OF ROTATION SELECTOR 

(FORWARD/REVERSE/CENTER LOCK) 

ADJUSTING TORQUE

See Figure 5

.

  There are sixteen torque indicator settings located on the 

front of the screwdriver.

  Rotate adjustment ring to desired setting, aligning num-

ber on adjustment ring with arrow on housing.

•   - 4 

For driving small screws

•  5 - 8 

For driving screws into soft material

•  9 -  

For driving screws into soft and hard  

 

 

materials

•  3 -  

For driving screws into hard wood

Содержание R81030

















Отзывы: