manualshive.com logo in svg

Ridetech 81214001, Руководство по решениям

Поделиться
Скачать
Ridetech 81214001 Скачать руководство пользователя страница 7

3. Bolt the compressor to the bracket.  Po-

sition the compressor on the Bracket in the 

orientaion shown.  Line up the holes in the 

(4) Mounting Bushings with the  (4) holes in 

the Bracket.  Install a #10 Flat Washer on 

each of the (4)  #10-24 x 1 1/4” Pan Head 

Screws.  Insert a Screw/Washer in each of 

the 4 holes.  Install a #10 Flat Washer on 

the threads sticking through the bottom of 

the bracket followed by a #10-24 Nylok Nut.  

Tighten the hardware.

NOTE:

The diagram shows the position the com-

pressor goes onto the plate.

4. The compressor needs to be mounted 

on the frame rail with the dryer up.   Attach 

the compressor bracket to the frame with (4) 

3/8”-16 x 1” Thread Forming Bolts supplied in 

the kit.  Drill a 5/16” Hole for the bolts. 

NOTE:

Before drilling any hole be sure to check and 

see if there are any brake lines, fuel lines, or 

wires on the other side of the surface you are 

drilling.

5. The Axle bracket can be mounted in any 

location on the axle tube to get the sensor 

linkage to line up.  The Axle mount should 

be mounted on the axle so that the linkage 

will line up from the axle mount to the sensor.  

Keep this in mind when establishing the sen-

sor location.

Page 3

Содержание 81214001













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды