Ricoh G104, Руководство по обслуживанию

Страница: 131 / 601

SERVICE MODE TABLE
SM 5-15 G104
Service
Tables
1004 079 DEV / OPC [K]: LS:
OHP
*EGB Adjusts the black development and OPC
motor speed.
[-4.00 to 4.00 /
-1.35 / 0.01 %/step]
1004 080 DEV [CMY]: LS: OHP *EGB Adjusts the color development motor speed.
[-4.00 to 4.00 /
0.0 / 0.01%/step]
1004 081 OPC [CMY]: LS: OHP *EGB Adjusts the color OPC motor speed.
[-4.00 to 4.00 /
-1.35 / 0.01%/step]
1004 082 Fusing: LS: OHP *EGB Adjusts the paper exit and fusing motor
speed.
[-4.00 to 4.00 /
0.6 / 0.01%/step]
1004 083 T.Belt: LS: OHP *EGB Adjusts the transfer belt motor speed.
[-4.00 to 4.00 /
0.0 / 0.01%/step]
1004 084 PFU: LS: OHP *EGB Adjusts the speed of the feed motor in the
optional paper tray unit.
[-4.00 to 4.00 /
-1.14 / 0.01%/step]
1004 085 Duplex: LS: OHP *EGB Adjusts the duplex motor speed.
[-4.00 to 4.00 /
-0.36 / 0.01%/step]
1006 [Phase Adjust.] Phase Adjustment
1006 001 Angle *EGB Adjusts the phase angle between the K drum
and the CMY drums.
[-180 to 180 /
0 / 1
°
/step] DFU
1104 [Fusing Cont.] Fusing Control
Control Method *EGB [0 or 1 / 1 / -] Alphanumeric 1104 001
Selects the fusing control method.
0: ON/OFF Control 1: PID Control (Phase control)
Max. Wait Time
*EGB [0 to 255 / 30 / 1 sec/step] 1104 022
Adjusts the maximum waiting time for the target printing temperature of fusing
unit. After this interval, printing will start if the temperature did not get to the
target.
Paper Feed. Temp.
*EGB
[0 to 30 / 5 / 1
°
/step]
1104 023
Adjusts the increase in the temperature of the fusing unit between the ready
condition and the start of paper feed at the start of a new job.
1st Add Time: LS
[0 to 50 / 0 / 0.1 sec/step] 1104 024
For print jobs at low speed. If the interval between jobs is less than this setting,
then the temperature change (1104 025) for the first page of a new job is not
applied.
1st Add Temp.
*EGB
[0 to 20 / 0 / 1
°
C/step]
1104 025
Adds this value to the basic fusing temperature, for the first page of a new job.
This extra temperature is necessary because when the printer starts the first
page, the fusing unit is not warm enough.
1st Temp. Maint.
*EGB [0 to 50 / 0 / 1 sec/step] 1104 026
Adjusts the time for maintaining the temperature change that is set with 1104
025.
1st Print Inter.
*EGB [0 to 100 / 0.2 / 0.1 sec/step] 1104 027
For print jobs at regular speed. If the interval between jobs is less than this
setting, then the temperature change (1104 025) for the first page of a new job
is not applied.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA