Ricoh D182 Скачать руководство пользователя страница 33

Страница: 33 / 124

OR-C2 Training

Slide 33

Import/Export of User Tool Settings Data - 1



To export data:



Insert an SD card into the slot on the side of the operation panel.



Use the following user tool: [System Settings] > [Administrator
Tools] > [Device Setting Information: Export (Memry Strge Devc)].



To import data:



Insert the SD card with the settings into the slot on the side of the
operation panel.



Use the following user tool: [System Settings] > [Administrator
Tools] > [Device Setting Information: Import (Memry Strge Devc)].



Specify whether to [Include] or [Exclude] the "Device Unique
Information". "Device Unique Information" includes the IP
address, host name, fax number, etc.



Specify an encryption key.



See the service manual for full details of operation.



Service Table > UP/SP Data Import/Export

No additional notes

Содержание D182





























































































































Результаты поиска

Содержание D182

Отзывы:

Похожие инструкции для D182

Бренды по названию

Популярные бренды

Ricoh D182, Обучение по обслуживанию

Результаты поиска

Содержание D182

Отзывы:

Похожие инструкции для D182

Бренды по названию

Популярные бренды