manualshive.com logo in svg

Rickard BW2011-2B, Руководство пользователя

Поделиться
Скачать
Rickard BW2011-2B Скачать руководство пользователя страница 9

 

 9 

RICKARD 2019

 

        

                  MLM INTEGRATION WITH BMS 

MCU 2 BACnet to BMS setup 

 
The MCU 2 supports both  BACnet/IP or BACnet ms/tp. Note MLM Tool V8.xx is required to bind the MCU 2 to 
other devices in a BACnet installation.  
The BACnet ms/tp MCU connects via a RS485 transceiver port to the ms/tp network, whereas BACnet /IP inter-
face to the Ethernet IP port on the MCU.  
Please  note  the  MCU  ms/tp  conforms  electrically  to  the  RS485  network  specification  as  recommended  by 
ASHRAE. The RS485 port on MCU 2 is optically isolated. For the interconnection and shielding instructions, refer 
to Addendum y of ANSI/ASHRAE Standard 135-2008. 
A major advantage of BACnet/IP implementation is that the MLM Tool application can run simultaneously with 
the BMS BACnet client on the same (PC) hardware platform. This greatly simplifies system commissioning and 
diagnostics.   
 

Bacnet/IP setup 

To configure a MCU 2 into a BACnet/IP network, connect to the MCU web page by entering the MCU 2 IP ad-
dress into an Internet browser. The default IP address is 192.168.0.251. The following information will be dis-
played on the web page: 



The Serial number and Software Version number - cannot be changed. 



The Device Name can be changed by the user and usually identify the physical location of the MCU. 



BACnet State indicates if the BACnet key has been activated, i.e. the BACnet/IP protocol is active on the 
MCU. 



The default unique BACnet device ID (instance) is derived from the Ethernet mac address. This parameter 
can be changed by the user (edit and press save) to comply with the BMS requirements. 



BACnet key entered to activate the BACnet protocol. This is a once-of setting normally activated during 
manufacture. To convert a MCU 2 Standard device to BACnet a key value can be procured from the man-
ufacturer and entered into this field.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
Note:  



The BACnet ID and Device Name fields indicated are contained in the Object Identifier and Object Name 
properties of the BACnet Device Object. 



To change MCU IP addresses consult the Hardware/Master Comms Unit section in the MLM Tool Help 
menu. 



To revert to the default IP address (192.168.0.251) press and hold the BOOT button on the MCU until the 
ST1 LED flashes. Release BOOT, press and release the DEF button. After a few seconds the CH1…4 LED’s 
will flash to indicate a reset condition. The IP address is now set to default.  

Содержание BW2011-2B



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды