Richmond GTR211 Скачать руководство пользователя

Страница: 1 / 28

GTR211 Installation Manual:

Rev 1

Sliding Gate Opener

User Manual

GTR211

WARNING

Instructions must be read before beginning installation. Please follow these instructions carefully, incorrect installation could

affect gate operation. If you require more information, please contact your local Richmond Wheel & Castor Co branch.

AU:

1300 474 246

NZ:

0800 61 71 81

International:

+613 9551 2233

For installation or troubleshooting assistance visit

gatesupport.richmondau.com

When mounting and positioning the motor ensure that the power cable is unplugged. The motor cover will need to be removed to mount

the motor to the mounting plate. Any changes to the settings of the gate motor can only be made by a licensed electrician.

Please Note: This motor is AC 240V Power only and is not compatible with DC Battery Backup or Solar power.

Gate in closed position

Gate in open position

Viewed from inside the property

Содержание GTR211





























Результаты поиска

Содержание GTR211

Отзывы:

Похожие инструкции для GTR211

Бренды по названию

Популярные бренды

Richmond GTR211, Руководство пользователя

Результаты поиска

Содержание GTR211

Отзывы:

Похожие инструкции для GTR211

Бренды по названию

Популярные бренды