Richdel 446PRi Скачать руководство пользователя страница 6

STEP 5: SET THE DAYS YOU WANT TO WATER
To 

set the watering days for each program:

A. Move the “DAYS” 

switch for “A” and "B" to the desired watering

day(s).“4”  (every 4th day), “3” (every 3rd day), “2” (every 2nd day),

“1” (every day), or “OFF”.

Zones programmed to water on a certain day will be watered
sequentially, skipping those zones programmed to “OFF”.

During watering, the zone number will appear on the left of the
display, and the zone’s run time will appear on the right. The
display starts at one minute and counts up to the total run time
before changing to the next zone to be watered.

S A M P L E   P R O G R A M

PROGRAM A(Lawn) PROGRAM B (Shrubs)

START TIME “IA”:

6 0 0 A

START TIME “2A”:

7 0 0 P

ZONE RUN TIMES

Zone #

Run Time (2-99 Min)

1 10

2 15
3 3 0
4 2 0
5
6
7
8
9

3. WATERING DAYS (Choose 1 only)

Every 4th day

(4)

Every 3rd day

(3)

Every 2nd day (2)
Every day

(1)  

OFF

START TlME ”1B”:  1 0 3 0   P

START TIME “2B”: -OFF-

Zone #

Run Time (2-99 Min)

3
4

5 5
6 6 0

7 1 0
8

1 0

9 6 0

WATERING DAYS (Choose 1 only)

Every 4th day

(4)

Every 3rd day

(3)

Every 2nd day (2) X
Every day

(1)

OFF

If you plan on connecting timer to a well pump or 

master 

valve, 

use the

following instructions.

A. Bring two wires up through the same hole used for the valve wiring.

B. Connect one wire to the terminal marked 

“PUMP”.

C. Connect the second wire to the terminal marked “COMM”.

D. If a master valve is required, the two wires should then be connected to

a master valve, rated at 24 VAC and a current no greater than 9 VA.

E. If a pump start relay is required, connect the two wires to an auxillary

relay with a coil rated at 24 VAC and a current no greater than 9 VA. The
relay’s contact would then be wired so it would supply voltage to the
pump’s contactor. A qualified electrician can make these connections

for you. 

Model SR-1 can be connected to the two wires and will directly

control a pump up to 2 HP at 240 VOLTS.

NOTE: The timer’s pump output will be turned on whenever a

zone is watering manually or automatically.

446PRi
T I M E R

I

FIGURE 2

10 11

Содержание 446PRi









Отзывы: