Jump start instructions:
Connect BLACK clamp (8) to negative (-) battery terminal.
Connect RED clamp (8) to positive (+) battery terminal.
Smart Jump Starter auto detects 12V or 24V – 12V(4) or 24V(6)
LED illuminates.
Start motor.
When motor starts, remove clamps immediately from battery
terminals.
Note:
For best performance, use Smart Jump Starter at 60% charge
capacity (3 LEDs) or higher. If 12V or 24V LED does not automatically
illuminate, check battery voltage and set 12V/24V manually via push buttons.
Charge 12V/24V Smart Jump Starter:
Connect Dual voltage AC wall adapter (9) to AC wall outlet, or connect car
adapter (10) to cigarette lighter port in vehicle.
Connect round-pin cable to Smart Jump Starter input port (1).
Five LEDs (3) flash in 20% increments and remain solid when corresponding
capacity is reached.
When fully charged, 5 solid LEDs briefly illuminate and then shut off - Remove
charge cable.
Note:
For optimum performance, make sure all LEDs have stopped flashing and remain
solid to ensure full charge capacity. Total recharge time (0% - 100%) = about 8 hours.
Push buttons:
TEST
(2)
Press/release – LEDs show remaining charge capacity
5 LEDs flashing = 10%; 1 LED solid = about 20%; 2
LEDs = about 40%; 3 LEDs = about 60%; 4 LEDs =
about 80%; 5 LEDs = 100% capacity Press/hold 3
seconds - resets battery (see troubleshooting)
12V
(5)
Press/hold 3 seconds – 12V LED illuminates
Ready to jump start 12V battery system
24V
(7)
Press/hold 3 seconds – 24V LED illuminates
Ready to jump start 24V battery system
Note:
Smart Jump Starter auto-detects most 12V/24V battery
systems. Press 12V/24V buttons when setting manually. 12V/24V
LEDs shut off in 30 seconds if no connection detected.
12V or 24V LED illuminates
Connected battery is 12V or 24V — OK
to jump start
12V or 24V LED flashes
Connected battery is 12V or 24V —
press corresponding 12V(5) or 24V(7)
button 3 seconds. When 12V or 24V
LED remains solid, start motor within
30 seconds
12V and 24V LEDs flash alternately
Correct voltage is not auto-detected
Check battery for correct voltage —
press corresponding 12V(5) or 24V(7)
button 3 seconds. When 12V or 24V
LED remains solid — start motor within
30 seconds
12V and 24V LEDs flash at the same
time
Connection error — connect battery
correctly and try again
12V or 24V LEDs do not illuminate
Battery may be completely dead
Check battery for correct voltage —
press corresponding 12V(5) or 24V(7)
button 3 seconds based on correct
voltage — start motor within 30 seconds
12V (4) / 24V (6) LED indicators:
C
D
Thank you for purchasing the RichardSolo 12V/24V Smart Jump Starter. Please read these instructions before operation
and save for future reference.
12V/24V Smart Jump Starter
INSTRUCTION MANUAL
1
8
5
7
3
Charge input port (15V 1A)
Test button
5 LED charge capacity indicators
(10%, 20%, 40%, 60%, 80%, 100%)
LED – 12V indicator
12V button
LED – 24V indicator
24V button
Battery clamps
Dual voltage (100-240V) AC wall adapter with
round pin cable (not shown)
Car adapter with round pin cable (not shown)
1
2
3
4
5
6
7
8
9
10
A
A
A
D
E
B
B
C
B
C
A
B
C
D
E
2
4
6
8
