12V/24V Smart Jump Starter
INSTRUCTION MANUAL
Continue
FAQ
Q: How does Smart Jump Starter identify12V or 24V batteries?
A: Under normal conditions, Smart Jump Starter automatically identifies the
battery voltage. If the battery is too low on power to identify, check battery for
voltage rating - press/hold 12V or 24V push button 3 seconds – start motor.
Q: What if Smart Jump Starter cannot identify the voltage automatically?
A: Most cars & light trucks use 12V. Larger trucks, diesel vehicles, and boats
may use 24V. Look for voltage rating on the vehicle’s battery, check owner’s
manual, or ask a professional.
Q: How many times will Smart Jump Starter start a vehicle before it
needs charging?
A: 12V battery = approximately 30 times. 24V battery = approximately 20
times. Total number may vary depending upon battery and starting conditions.
Notes
• For best performance, use Smart Jump Starter with
60% remaining charge capacity (3 LEDs) or higher
• For manual voltage setting, make sure 12V or 24V is
switched on before connecting clamps to battery
terminals
• DO NOT connect clamps to 12V battery when 24V
LED is illuminated on Smart Jump Starter
• DO NOT connect clamps to 24V battery when 12V
LED is illuminated on Smart Jump Starter
• When 12V or 24V LED illuminates DO NOT connect
clamps to wrong +/- battery terminals — RED = (+)
positive / BLACK = (-) negative
• DO NOT connect RED/BLACK clamps(8) together
• Make sure Smart Jump Starter clamps(8) are connected
securely to battery terminals
• Always remove clamps(8) within 30 seconds after motor
starts
• Check battery terminals for rust, dirt and corrosion before
using Smart Jump Starter — clean if necessary to avoid
poor performance
• DO NOT jump start again after 3 attempts to avoid damaging
Smart Jump Starter / Check for other vehicle issues
• NEVER disassemble Smart Jump Starter —
NO serviceable parts inside
• Charge only with Smart Jump Starter AC(9) or car
adapter(10)
Troubleshooting
Problem:
No response when TEST button is pressed
Cause:
Smart Jump Starter is low on power / low voltage
protection mode activated
Solution:
Plug AC (9) or Car(10) adapter into 15V 1A port(1)
and recharge Smart Jump Starter
Problem:
12V(4) and 24V(6) LED indicators are flashing
at the same time
Cause:
Short circuit detected / Smart Power Bank locked
in self protection mode
Solution:
Disconnect clamps(8) from short circuit / press
TEST(2) button 3 seconds to reset
Problem:
12V(4) and 24V(6) LED indicators
twinkle frequently when connected to battery
Cause:
Red(+) and black (-) cables are
connected to wrong battery terminal
Solution:
Disconnect both clamps(8) from
battery / reconnect to c/- battery
terminal
Q: How long does it take to fully recharge Smart Jump Starter?
A: About 8 hours through its 15V 1A charge input port (1).
Q: What is the lifetime for Smart Jump Starter?
A: Up to 5 years.
Q: How often should Smart Jump Starter be recharged?
A: A fully charged unit will last about 6-12 months. Recharge every 3 months in
storage. For best performance, use Smart Jump Starter with 60% charge
capacity (3 solid LEDs) or higher.
Note:
It’s a good idea to top up the charge as often as you want — keeping it
fully charged is fine. No need to wait till depleted.
Questions? Please email us at: [email protected] 2301 Kerner Blvd. Suite C, San Rafael, CA 94901 USA www.RichardSolo.com
Specifications:
Capacity: 24000 mAh (88.8 Wh)
Input: DC 15V 1A
Output: 12V jump start / 24V
jump start
Start current: 500A-12V /
250A-24V
Peak current: 1000A-12V /
500A-24V
Size: 9.26" x 8.86" x 3.15" (23.5
x 22.5 x 8.0 cm)
Weight: 3.64 lb (1.65 kg)
Operating temperature: -4~140
degrees F (-20~60C)
Car adapter charge cable
length: 36" (91.44 cm)
Dual voltage AC wall adapter
charge cable length:
52 (132.1 cm)
Charging time: 8 hours
Package Contents:
• 12V/24V Smart Jump Starter
• Dual voltage (100-240V) AC
wall adapter with round pin
cable
• Car adapter with round pin
cable
• Instructions
Toxic and
harmful
substances
Pb:0 Hg:0 Cd:0 Cr(Vi):0
PBB:0 PBDE:0
Note:
0 indicates all homogeneous
materials’ hazardous substances
content are below the MVC limit
specified in the Standard 2002/95/
EC(RoHs)wait till depleted.
Safety Instructions:
Read all instructions and notes
prior to using this product. Failure
to read and follow safety
instructions could result in fire,
explosion, electrical shock or other
hazard causing serious and/or fatal
injury and/or property damage
1. Do not modify, disassemble,
open, drop, crush, puncture, or
shred this product
2. Do not expose this product to
rain or water
3. Avoid excessive heat (open
flame, sunlight, etc.)
4. Do not store in locations where
temperature may exceed 158
degrees F (70C)
5. Recharge Smart Jump Starter in
ambient temperatures between
32-104 degrees F (0-40C)
6. Do not use near flammable
liquids, gasses, or dust
7. This product is not a toy — keep
away from children
