background image

Vehicle Scale Limited Warranty

19

8.0  Vehicle Scale Limited Warranty

Rice Lake Weighing Systems (RLWS) warrants that all RLWS brand equipment and systems properly installed 
by a Distributor will operate in accordance with written specifications as confirmed by the Distributor and 
accepted by RLWS. All systems and components are warranted against defects in materials and workmanship for 
2 years from date of shipment from the manufacturer. Furthermore, the seller warrants the fabricated 
weighbridge against faulty workmanship and defective materials for 5 years from the date of shipment from the 
manufacturer.

RLWS warrants that the equipment sold hereunder will conform to the current written specifications authorized 
by RLWS. RLWS warrants the equipment against faulty workmanship and defective materials. If any equipment 
fails to conform to these warranties, RLWS will, at its option, repair or replace such goods returned within the 
warranty period subject to the following:

Upon discovery by Buyer of such non-conformity, RLWS will be given prompt written notice with a 
detailed explanation of the alleged deficiencies.

Individual electronic components returned to RLWS for warranty purposes must be packaged to prevent 
electrostatic discharge (ESD) damage in shipment. Packaging requirements are listed in a publication, 
“Protecting Your Components From Static Damage in Shipment,” available from RLWS Equipment 
Return Department.

Examination of such equipment by RLWS confirms that the non-conformity actually exists, and was not 
caused by accident, misuse, neglect, alteration, improper installation, improper repair, or improper 
testing. RLWS shall be the sole judge of all alleged non-conformities.

Such equipment has not been modified, altered or changed by any person other than RLWS or its duly 
authorized repair agents.

RLWS will have a reasonable time to repair or replace the defective equipment. Buyer is responsible for 
shipping charges both ways.

Vehicle scale products are eligible for warranty labor and mileage charges with pre-approval by RLWS 
Service Department, and only to the limits described in the vehicle scale reimbursement program.

RLWS will not be liable for the cost of any repairs made by others.

T

HESE

 

WARRANTIES

 

EXCLUDE

 

ALL

 

OTHER

 

WARRANTIES

EXPRESSED

 

OR

 

IMPLIED

INCLUDING

 

WITHOUT

 

LIMITATION

 

WARRANTIES

 

OF

 

MERCHANTABILITY

 

OR

 

FITNESS

 

FOR

 

A

 

PARTICULAR

 

PURPOSE

. N

EITHER

 

RLWS 

NOR

 

DISTRIBUTOR

 

WILL

 

BE

 

LIABLE

 

FOR

 

INCIDENTAL

 

OR

 

CONSEQUENTIAL

 

DAMAGES

RLWS 

AND

 

BUYER

 

AGREE

 

THAT

 RLWS’ 

SOLE

 

AND

 

EXCLUSIVE

 

LIABILITY

 

HEREUNDER

 

IS

 

LIMITED

 

TO

 

REPAIR

 

OR

 

REPLACEMENT

 

OF

 

SUCH

 

GOODS

. I

N

 

ACCEPTING

 

THIS

 

WARRANTY

THE

 

BUYER

 

WAIVES

 

ALL

 

OTHER

 

CLAIMS

 

TO

 

WARRANTY

.

S

HOULD

 

THE

 

SELLER

 

BE

 

OTHER

 

THAN

 RLWS, 

THE

 

BUYER

 

AGREES

 

TO

 

LOOK

 

ONLY

 

TO

 

THE

 

SELLER

 

FOR

 

WARRANTY

 

CLAIMS

.

No terms, conditions, understanding, or agreements purporting to modify the terms of this warranty shall have 
any legal effect unless made in writing and signed by a corporate officer of RLWS and the Buyer.

2001 Rice Lake Weighing Systems, Inc. Rice Lake, WI USA.  All Rights Reserved.

RICE LAKE WEIGHING SYSTEMS  • 230 WEST COLEMAN STREET  • RICE LAKE, WISCONSIN 54868  • USA

Содержание SURVIVOR PT
























Отзывы: