Rice Lake Revolution 680 Synergy Plus, Техническое руководство

Страница: 55 / 80

EDP Commands
© Rice Lake Weighing Systems ● All Rights Reserved 49
7.8 Feature Commands
7.9 Regulatory Commands
Command Description Values
DATEFMT Date format MMDDYY (default), DDMMYY, YYMMDD, YYDDMM
DATESEP Date separator SLASH (default), DASH, SEMI, DOT
TIMEFMT Time format 12HOUR (default), 24HOUR
TIMESEP Time separator COLON (default), COMMA, DOT
CONSNUM Consecutive numbering 0–9999999, 0 (default)
CONSTUP Consecutive number start-up value 0–9999999, 0 (default)
UID ID of the indicator Up to 6 alphanumeric characters, 1 (default)
KYBDLK Keyboard lock (disable keypad) OFF (default), ON
ZERONLY Disable all keys except ZERO OFF (default), ON
CONTACT.COMPANY Contact company name Up to 30 alphanumeric characters
CONTACT.ADDR1-3 Contact company address Up to 30 alphanumeric characters (for each line)
CONTACT.NAME1-3 Contact names Up to 30 alphanumeric characters (for each line)
CONTACT.PHONE1-3 Contact phone numbers Up to 30 alphanumeric characters (for each line)
CONTACT.EMAIL Contact e-mail address Up to 30 alphanumeric characters.
CONTACT.NEXTCAL Next calibration date Date MMDDYYYY as an 8-digit number.
CONTACT.LASTCAL Last calibration date Date MMDDYYYY as an 8-digit number.
LOCALE Enable gravity compensation OFF (default), ON
LAT.LOC Origin latitude (to nearest degree) for gravity compensation 0–90, 45 (default)
ELEV.LOC Origin elevation (in meters) for gravity compensation -9999–9999, 345 (default)
DEST.LAT.LOC Destination latitude (in degrees) for gravity compensation 0–90, 45 (default)
DEST.ELEV.LOC Destination elevation (in meters) for gravity compensation -9999–9999, 345 (default)
Table 7-8. Feature Commands
Command Description Values
REGULAT Regulatory mode NTEP (default), CANADA, INDUST, NONE, OIML
AUDAGNCY Audit Agency (Industrial Mode) NTEP (default), CANADA, NONE, OIML
REG.SNPSHOT Display or Scale weight source DISPLAY (default), SCALE
REG.HTARE Allow tare in display hold NO (default), YES
REG.ZTARE Remove tare on ZERO NO (default), YES
REG.KTARE Always allow keyed tare NO, YES (default)
REG.MTARE Multiple tare action REPLACE (default), REMOVE, NOTHING
REG.NTARE Allow negative tare NO (default), YES
REG.CTARE Allow Clear key to clear tare/accumulator NO, YES (default)
REG.NEGTOTAL Allow total scale to display negative value NO (default), YES
REG.PRTMOT Allow print while in motion NO (default), YES
REG.PRINTPT Add PT to keyed tare print NO, YES (default)
REG.PRTHLD Print during display hold NO (default), YES
REG.HLDWGH Allow weighment during display hold NO (default), YES
REG.MOTWGH Allow weighment in motion NO (default), YES
REG.OVRBASE Zero base for overload calculation CALIB (default), SCALE
REGWORD Regulatory word GROSS (default), BRUTTO
REG.RTARE Round the Pushbutton Tare NO (default), YES
REG.RKTARE Round the Keyed Tare NO (default), YES
REG.AZTNET Perform AZT on Net value NO (default), YES
REG.MANUALCLEARTARE Allows manual clearing of the tare value NO, YES (default)
REG.TAREINMOTION Allows Tare in Motion NO (default), YES
REG.ZEROINMOTION Allows scale to be zeroed while in motion NO (default), YES
REG.UNDERLOAD Underload weight value in display divisions 1–9999999, 20 (default)
Table 7-9. Regulatory Commands