Rheem Water Heater Скачать руководство пользователя страница 3

Страница: 3 / 63

CONTENTS

HOUSEHOLDER – We recommend you read pages 4 to 25.

The other pages are intended for the installer but may be of interest.

About Your Water Heater............................................................4

How Your Water Heater Works.................................................11

Regular Care ..............................................................................13

Timer Operation.........................................................................16

Save A Service Call ...................................................................21

Installation – Solar Storage Tank.............................................26

Installation – Solar Collectors ..................................................36

Connections – Plumbing ..........................................................39

Connections – Electrical...........................................................43

Commissioning..........................................................................45

Lighting The Water Heater........................................................48

Draining The Solar Collectors ..................................................52

Draining The Water Heater .......................................................53

Water Supplies...........................................................................56

Warranty .....................................................................................58

Warning:

Upon completion of the installation and commissioning of the

water heater, leave this guide with the householder or a responsible officer.

DO NOT

leave this guide inside of the cover of the water heater, as it may

interfere with the safe operation of the water heater or ignite when the water
heater is turned on.

Содержание Water Heater
































































Результаты поиска

Содержание Water Heater

Отзывы:

Rheem Water Heater, Руководство пользователя, Страница: 3 / 63

Результаты поиска

Содержание Water Heater

Отзывы: