Rheem Stellar 850330 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 44

background image

4

ABOUT YOUR WATER HEATER

WATER HEATER APPLICATION

This water heater is designed for use in a single family domestic dwelling for
the purpose of heating potable water. Its use in an application other than this
may shorten its life.

MODEL TYPE

The Rheem

®

water heater model you have chosen is

suitable for outdoor installation only. The model is a
high efficiency, quick recovery 850 series Stellar

™

water heater.

Water is stored in a vitreous enamel lined steel cylinder
and heated by a gas burner located under the cylinder.
The  heat  produced  by  the  burner  is  transferred  to  the
water through the base, top and wall of the cylinder and
through the wall of a flue pipe which passes through the
centre  of  the  cylinder.  A  flue  baffle  in  this  flue  ensures
the  efficiency  of  the  water  heater  is  correct.  The  gas
supply  to  the  burner  is  controlled  by  the  thermostat  so
the water is heated to a constant temperature.

Automatic  safety  controls  are  fitted  to  the  water  heater  to  provide  safe  and
efficient operation.

HOW HOT SHOULD THE WATER BE?

The  water  heater  features  a  user  adjustable
thermostat,  which  allows  you  to  personally
choose the most suitable temperature for your
hot  water  needs.  Refer  to

“Temperature

Adjustment”

on page 5.

To meet the requirements of the National
Plumbing Standard the temperature of the
stored water must not be below 60°C.

Note:

AS 3498 requires that a water heater

provides  the  means  to  inhibit  the  growth  of
Legionella  bacteria  in  potable  water.  This
water  heater  can  satisfy  this  AS 3498
requirement  provided  it  is  operating  and  the
thermostat setting is 60°C or higher, including
when  it  is  used  as  an  in-series  booster  water
heater for a solar water heater.

maximum thermostat

setting

maximum

recommended supply

temperature to

bathrooms and

ensuites

minimum

recommended stored

water temperature

«
...
2
3
4
5
6
...
»

Содержание Stellar 850330













































Отзывы:

Нет отзывов

Похожие инструкции для Stellar 850330

Бренд: Danfoss Страницы: 72

Бренд: Zilmet Страницы: 10

Бренд: Rainfresh Страницы: 10

Бренд: salmson Страницы: 49

Бренд: Gabarron Страницы: 8

Бренд: KEKAI Страницы: 12

Бренд: Pacetti Страницы: 12

Бренд: Gude Страницы: 64

Бренд: Stübbe Страницы: 32

Sanitizer Plus ASP1-1044

Бренд: Water Right Страницы: 30

Electric iSUP Air Pump

Бренд: Bluefin SUP Страницы: 21

Бренд: Rinnai Страницы: 31

Бренд: REMKO Страницы: 20

Taro HCS SJ Series

Бренд: Texmo Industries Страницы: 41

Бренд: EBARA Страницы: 20

Бренд: BM2 BIEMMEDUE Страницы: 8

Бренд: Oasis Aquatics Страницы: 14

GOULDS e-SVI Series

Бренд: Xylem Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды