Rheem 90RS04EES Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

background image

21

FIGURE 14

COMBUSTION AIR FITTING

UPFLOW

DOWNFLOW/HORIZONTAL

2" PVC
DOUBLE
ELBOW

TOP
OPTION

EXHAUST

2" PVC ELBOW

SIDE
OPTION

2" PVC
DOUBLE
ELBOW*

COMBUSTION AIR

EXHAUST

ATTACH DOUBLE ELBOW TO INTAKE AIR
COLLAR AND SECURE WITH TWO SHEET
METAL SCREWS TO PREVENT ACCIDENTAL
BLOCKAGE OF INTAKE AIR OPENING.

*NOTE: WHEN FURNACE IS INSTALLED IN A
HORIZONTAL POSITION ONLY ONE 90°
ELBOW IS REQUIRED. INSTALL THE ELBOW
SO THE OPEN END IS POINTED DOWNWARD.

ATTACH DOUBLE ELBOW TO TOP INLET
AIR OPENING OR 90° ELBOW TO SIDE
INLET AIR OPENING TO PREVENT
ACCIDENTAL BLOCKAGE OF INTAKE
OPENING. PLUG OPENING NOT USED.

I337

I336

Method 2
(Not Shown)
One permanent opening, located
within 12 inches of the top of the
enclosure, shall be permitted
where the equipment has
clearances of at least 1 inch from
the sides and back and 6 inches
from the front of the appliance.
The opening shall directly
communicate with the outdoors or
communicate through a vertical or
horizontal duct to the outdoors or
spaces (crawl or attic) that freely
communicate with the outdoors,
and shall have a minimum free
area of:

a. 1 square inch for each 3,000

BTUH of the total input rating of
all equipment located in the
enclosure and

BTUH

Free Area

Round Pipe

Input

Each Opening

Size

45,000

15.00 square inches

4"

60,000

16.67 square inches

5"

75,000

25.00 square inches

6"

90,000

30.00 square inches

6"

105,000

35.00 square inches

7"

120,000

40.00 square inches

7"

b. Not less than the sum of the

areas of all vent connectors in
the confined space.

If unit is installed where there is an
exhaust fan, sufficient ventilation
must be provided to prevent the
exhaust fan from creating a negative
pressure.

Combustion air openings must not be
restricted in any manner.

CONSULT LOCAL CODES FOR
SPECIAL REQUIREMENTS.

CONNECTION TO
FURNACE

IMPORTANT:

When indoor

combustion air is used, the inlet air
opening at the furnace must be
protected from accidental blockage.
On upflow models, install a 90° elbow
pointing downward in the side inlet air
opening or a double elbow pointing
downward in the top inlet air opening.
On downflow/horizontal models,
install a double elbow in the top inlet
air opening. See Figure 14.

«
...
19
20
21
22
23
...
»

Содержание 90RS04EES Series





























































Отзывы:

Нет отзывов

Похожие инструкции для 90RS04EES Series

Бренд: Daikin Страницы: 64

Бренд: Daikin Страницы: 68

Бренд: Daikin Страницы: 16

Бренд: York Страницы: 44

PowerHeat 980 Pro CHH-980

Бренд: Quest Engineering Страницы: 30

Бренд: Coleman Страницы: 12

Бренд: Lennox Страницы: 4

Бренд: Maytag Страницы: 36

Amana M9S80-U Series

Бренд: Maytag Страницы: 36

Amana CES9 Series

Бренд: Maytag Страницы: 56

Бренд: Luxaire Страницы: 8

Бренд: Heat Controller Страницы: 4

Бренд: Heat Controller Страницы: 14

Comfort Aire GLUA105E5B

Бренд: Heat Controller Страницы: 64

Бренд: Heat Controller Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды