Rheem 55027500 Скачать руководство пользователя страница 52

TM017 Rheem Air Sourced Heat Pump Service Instructions REV: C 
Date of Issue: 5/11/05 

This document is stored and maintained electronically by 

 Service. All printed copies not bearing this statement in RED are deemed “uncontrolled”. 

51

Rheem Electric Water Heater Warranty - (Australia Only) 

 

Notes: 

The Sealed Refrigeration System includes components that carry refrigerant only e.g. Compressor, 
Condenser, TX valve, Receiver/Drier, Evaporator and associated pipe work.

 

 

WARRANTY CONDITIONS 

1. 

This warranty is applicable only to Rheem water 
heaters manufactured from 1

st

 January 2001. 

2. 

The water heater must be installed in 
accordance with the Rheem water heater 
installation instructions, supplied with the water 
heater, and in accordance with all relevant 
statutory and local requirements of the State in 
which the water heater is to be installed. 

3. 

Where a failed component or water heater is 
replaced under Warranty, the balance of the 
original period will remain effective. The replaced 
part or water heater does not carry a new 
warranty.  

4. 

Where the water heater is installed outside the 
boundaries of a metropolitan area as defined by 
Rheem or further than 25 km from a regional 
Rheem Service branch office, or an 

Accredited Service Agent, the cost of transport, 
insurance and travelling costs between the 
nearest Rheem Australia Accredited Service 
Agent’s premises and the installed site shall be 
the owner’s responsibility. 

5. 

The warranty only applies to the water heater 
and original or genuine company component 
replacement parts and therefore does not cover 
any plumbing or electrical parts supplied by the 
installer and not an integral part of the water 
heater, e.g. pressure limiting valve; isolation 
valves; non-return valves; electrical switches; 
pumps or fuse. 

6. 

The water heater must be sized to supply the hot 
water demand in accordance with the guidelines 
in Rheem water heater literature. 

 

WARRANTY EXCLUSIONS 

1. 

REPAIR AND REPLACEMENT WORK WILL BE CARRIED OUT AS SET OUT IN THE RHEEM WATER 
HEATER WARRANTY ABOVE, BUT THE FOLLOWING EXCLUSIONS MAY CAUSE THE WATER 
HEATER WARRANTY TO BECOME VOID, AND MAY INCUR A SERVICE CHARGE AND COST OF 
PARTS. 

 

a) 

Accidental damage to the water heater or 
component including: Acts of God; failure due 
to misuse; incorrect installation; attempts to 
repair the water heater other than by a Rheem 
Service Accredited Service Agent or the Rheem 
Service Department. 

b) 

Where it is found there is nothing wrong with 
the water heater; where the complaint is related 
to excessive discharge from the temperature 
and pressure relief valve due to high water 
pressure; where there is no flow of hot water 
due to faulty plumbing; where water leaks are 
related to plumbing and not the water heater 
components; where there is a failure of gas, 
electricity or water supplies; where the supply 
of gas, electricity or water does not comply with 
relevant codes or acts. 

c) 

Where the water heater or water heater 
component has failed directly or indirectly as a 
result of: excessive water pressure, 
temperature and/or thermal input or corrosive 
atmosphere. 

d) 

Where the water heater is located in a position 
that does not comply with the Rheem water 
heater installation instructions or relevant 
statutory requirements, causing the need for 
major dismantling or removal of cupboards, 
doors or walls, or use of special equipment to 
bring the water heater to floor level. 

e) 

Repairs to the water heater due to scale 
formation in the waterways when the water 
heater has been connected to a harmful water 
supply as outlined in the Owner’s Guide and 
Installation Instructions booklet.     

 

2.  SUBJECT TO ANY STATUTORY PROVISIONS TO THE CONTRARY, THIS WARRANTY EXCLUDES 

ANY AND ALL CLAIMS FOR DAMAGE TO FURNITURE, WALLS, FOUNDATIONS OR ANY OTHER 
CONSEQUENTIAL LOSS EITHER DIRECTLY OR INDIRECTLY DUE TO LEAKAGE FROM THE 
WATER HEATER. 

In addition to this warranty, the Trade Practices Act 1974 and similar laws in each state and territory provide 
the owner under certain circumstances with certain minimum statutory rights in relation to your Rheem water 
heater. This warranty must be read subject to that legislation and nothing in this warranty has the effect of 
excluding or restricting those rights. 
 

Rheem Australia Pty Ltd 
A.B.N 21 098 823 511 

FOR SERVICE TELEPHONE 

131 031 AUSTRALIA

or refer local Yellow Pages

 

NOTE: Every care has been taken to ensure accuracy in preparation of this publication. No liability can be accepted for any 

consequences, which may arise as a result of its application. 

 

Содержание 55027500






















































Отзывы: