manualshive.com logo in svg

Rheem 10143267, Инструкция по эксплуатации, Страница: 40 / 60

Поделиться
Скачать
Rheem 10143267 Скачать руководство пользователя страница 40

 

TM090 12-26 Series II CFGWH Service Instructions 
REV AB 

– Issued February 2019 

 

This document is stored and maintained electronically by Rheem Technical Support. All printed copies 

are deemed “uncontrolled”

 

40 

Fault Finding Chart 2 

 

 

 

 

System Not Ready

YES

Check for damage in the combustion 

chamber. If no damage present, replace 

over temperature limiter and check 

minimum and maximum burner pressures

NO

Overheating

NO

Test 2

Replace the PCB assembly.

YES

Replace the remote controller cable.

YES

Duplicate remote controller fitted. Up to 3 

remotes can be fitted but can only be one 

of each type of controller (K, B1, B2).

NO

Communication 

failure

NO

Fan detecting 

circuit failure

YES

*Refit  connector L 

and restore power.

NO

* WARNING

Disconnect power prior to 

removing or inserting 

connector plugs

Replace the fan motor.

Error code due to supply voltage drop.

NO

Replace the PCB assembly.

YES

NO

Remove and reinsert 

the gas type 

connector.

YES

Gas type connector was originally not 

inserted correctly.

Faulty gas type connector - replace.

YES

NO

Gas type connector 

malfunction

2

YES

*Remove  connector L 

from the fan motor and 

restore power

Test 16

Test 10

Test 6

NO

NO

Replace the lower gas burner assy 

assembly.

NO

Replace the GIS valve assembly.

YES

YES

Replace the heat exchange thermistor.

Is the

resistance of the over 

temp limiter normal?

Is the voltage and 

resistance of S1,S2, S3 

normal?

Is voltage and resistance 

of  GISV normal?

Is the voltage and 

resistance of

heat exchange 

thermistor normal?

YES

NO

Is the remote 

controller cable 

open circuit?

YES

NO

Is error code 14

displayed?

Is error code 71

displayed?

Is error code 76 

displayed?

Is error code 79 

displayed?

Is error code 82 

displayed?

Is error code 82 

redisplayed?

Is error code 79 

redisplayed?

Is error code 79 

redisplayed?

NO

YES

Replace the PCB assembly.

Replace the PCB assembly.

NO

Has the fan the 

correct voltage?

Is gas type 

connector fitted?

YES

Gas type connector must be 

connected. Locate GTC within 

heater cabinet and insert.

NO

Содержание 10143267





























































Отзывы:

Нет отзывов