Rheem 10143267 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 60

Rheem 10143267 Скачать руководство пользователя страница 39

TM090 12-26 Series II CFGWH Service Instructions
REV AB

– Issued February 2019

This document is stored and maintained electronically by Rheem Technical Support. All printed copies

are deemed “uncontrolled”

39

Fault Finding Chart 1

Voltages up to 240 volts will be present within the water heater, take care
not to touch wiring terminals. Use an insulated tool when operating the DIP
switch or MIN and MAX buttons.

Power Supply

NO

No power supply. Check household

wiring.

YES

Test 1

Cordset open circuit? - replace.
Inline fuses open circuit

– replace.

Internal wiring from terminal block
open circuit

– repair.

NO

YES

Remote controller cable open
circuit

– repair / replace.

Remote controller failed

– replace.

YES

PCB failed

– replace.

NO

1

Turn DIP switch 1 on.

Is 240 volts AC present

at the power point?

Is 240 volts AC present

at the PCB?

Is OK monitor

display ON?

(1E displayed?)

Test 18

«
...
37
38
39
40
41
...
»

Содержание 10143267





























































Отзывы:

Нет отзывов