C A D E D O U B L E B AT H S C O N C E
All wires are connected. When unpacking, be careful not to pull wires,
as a bad connection may result. Do not connect electricity until your
fixture is fully assembled. To reduce the risk of fire, electrical shock
or personal injury, always turn off fixture and allow it to cool prior to
replacing the lightbulb. Do not touch bulb when fixture is turned on
or look directly at lit bulb. Keep flammable materials away from the lit
bulb.
This lighting fixture contains lead, a chemical known to the State of
California to cause cancer, birth defects and other reproductive harm.
Wash hands after installing, handling, cleaning or otherwise touching
this light fixture.
When using a dimmer device with this fixture, a specific electronic low
voltage (ELV) dimmer must be used to avoid potential damage to the
transformer.
WARNING: This product can expose you to lead, which is
known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information, go to
www.P65Warnings.ca.gov.
IMPORTANT PLEASE READ
WE RECOMMEND INSTALLATION BY A
LICENSED ELECTRICIAN.
SAFET Y INSTRUC TIONS:
VERTICAL MOUNTING: FIG. A
WARNINGS:
These instructions are provided for your safety. It is very important
that they are read completely before beginning the installation of your
fixture.
This fixture ships with two non-replaceable solid-state LEDs installed.
If any special control devices are used with this fixture, follow the
instructions carefully to assure full compliance with N.E.C.
requirements. If there are any questions, contact a qualified electrical
contractor.
1. Remove all parts carefully from the box and remove all plastic
coverings.
2. Remove glass shades (A) by unscrewing from threaded socket
cover (B).
3. Remove backplate screws (C) from backplate (D).
4. Carefully position adapter plate (G) behind mounting plate (F). Guide
wires from fixture through hole (J) on mounting plate (F) and hole (K),
located on adapter plate (G).
5. Make proper electrical connection with wiring exiting hole of adapter
plate (G).
6. Connect ground wire (green) from the fixture to the ground wire in
outlet box. Connect the black wires of the fixture (or smooth side of
the wire) to the black wire in the outlet box using wire nuts (H).
Connect the white wires of the fixture (or rough side of the wire) to
the white wire in the outlet box using wire nuts (H).
7. Affix mounting plate (F) and adapter plate (G) to “J BOX” by inserting
mounting plate screw (I) into slotted hole on bottom of mounting
plate (F) and slotted hole on bottom of adapter plate (G). Thread
screw (I) into bottom hole of “J BOX.”
8. After mounting plate and adapter plate are moved into desired
position, insert mounting plate screw (E) into slotted hole in top of
mounting plate (F) and slotted hole in top of adapter plate (G) and
thread screw (E) into drywall above “J BOX”. Make sure to use
threaded plastic sleeve (included) with mounting plate screw (E)
when attaching fixture to drywall.
9. Align holes in top and bottom of backplate (D) with screw holes in
top and bottom of mounting plate (F).
10. Place backplate (D) over mounting plate (F). Thread backplate
screws (C) into backplate (D) to secure fixture to mounting plate (F).
11. Align threaded section of glass shades (A) with threaded openings
of socket cover (B). Thread glass shades (A) onto threaded socket
cover (B) until tight.
THIS PRODUC T IS NOT A TOY AND THE PRODUC T HAS
NO PLAY VALUE.
WARNING: STRANGULATION HAZARD
Keep cord at least 3 feet away from cribs, bassinets, and toddler beds.
Keep out of reach of children under 3 years of age.
ASSEMBLY & INSTALLATION
Wipe clean with a soft, dry cloth or static duster. Always avoid the use of
harsh chemicals or abrasive cleaners, as they may cause damage to the
fixture’s finish.
CARE INSTRUC TIONS:
2 of 3
SHUT OFF MAIN ELECTRICAL SUPPLY FROM THE MAIN BREAKER.
