RFL Electronics 9508D UCC, Инструкция по эксплуатации

Страница: 8 / 243

RFL 9508D UCC RFL Electronics Inc.
September 7, 2012 viii (973) 334-3100
TABLE OF FIGURES
Figure 2-1. Typical point-to-point application ...................................................................................................................... 2-2
Figure 2-2. Concatenated Point-to-Point Links with incorporated branch exchange ............................................................ 2-4
Figure 2-3. PLC-TT Applications ......................................................................................................................................... 2-7
Figure 3-1. Mounting dimensions for 50W system, RFL 9508D UCC Digital PLC, lower shelf is the multiplexing unit... 3-3
Figure 3-2. Mounting dimensions for 100W system, RFL 9508D UCC digital powerline Carrier....................................... 3-4
Figure 3-3. Rear Panel Wiring Of Typical RFL 9508D UCC, 4W System, 50W Chassis.................................................. 3-11
Figure 3-4. Rear Panel Wiring Of Typical RFL 9508D UCC, 4W System, 100W Chassis................................................ 3-12
Figure 4-1. RFL 9508D NMS initial installation window..................................................................................................... 4-3
Figure 4-2. Program Settings................................................................................................................................................. 4-5
Figure 4-3. PC directly connected to a node using an RS-232 cable..................................................................................... 4-6
Figure 4-4. PC connected to a node from a remote location ................................................................................................. 4-6
Figure 4-5. Remote configuration of a PLC terminal............................................................................................................ 4-7
Figure 4-6. Construction of a typical RS-232 cable between the PC and a MA470 ............................................................. 4-7
Figure 4-7. PC at a remote location connected to 4 nodes, where each node is a different network..................................... 4-8
Figure 4-8. PC at a remote location connected to 2 nodes, where all nodes are in the same network................................... 4-9
Figure 4-9. Typical network and communication path........................................................................................................ 4-10
Figure 4-10. 9508D NMS starting window ......................................................................................................................... 4-11
Figure 4-11. Terminal Unit selection window..................................................................................................................... 4-12
Figure 4-12. RFL9508D UCC NMS presentation window ................................................................................................. 4-13
Figure 4-13. Digital XCVR Channel Settings Window ...................................................................................................... 4-15
Figure 4-14. Analog XCVR Channel settings window ....................................................................................................... 4-17
Figure 4-15. Analog XCVR channel administrator settings window .................................................................................. 4-19
Figure 4-16. CM4 configuration window............................................................................................................................ 4-22
Figure 4-17. Configuration parameters for PLC-TT card ................................................................................................... 4-24
Figure 4-17. PLC-TT card’s status window ........................................................................................................................ 4-28
Figure 5-1. Front View Of RFL 9508D Chassis Showing Controls And Indicators ............................................................. 5-1
Figure 5-2. Module Placement in a Typical RFL 9508D Digital Chassis (Top View) ......................................................... 5-3
Figure 5-3. Digital chassis showing the installation of two PLC-TT Module Adapters........................................................ 5-6
Figure 5-4. Module Placement in a Typical RFL 9508D RF Chassis (Top View)................................................................ 5-8
Figure 5-5. Cable connections in the RF Chassis ................................................................................................................ 5-11
Figure 5-6. Module placement in auxiliary 3U RF Chassis for 100W Systems (Top View) .............................................. 5-12
Figure 5-7. Module placement for 9508RT......................................................................................................................... 5-13
Figure 5-8. Packetizing unit rear view ................................................................................................................................ 5-14
Figure 5-9. Location of jumpers on CM4 common module ................................................................................................ 5-17
Figure 5-10. Location and use of setup jumpers on MA-271 and MA-278 Module Adapters............................................ 5-19
Figure 5-11. Location of DIP switch SW1 on typical Optical Interface Adapter................................................................ 5-20
Figure 5-12. Location of jumpers on PLC-TT module........................................................................................................ 5-21
Figure 5-13. Location and use of voltage control jumpers on a typical I/O adapter module input board ........................... 5-22
Figure 5-14. Location of LEDs on Transceiver module...................................................................................................... 5-23
Figure 5-15. MA-470 Module Adapter, rear panel view and pinouts ................................................................................. 5-26
Figure 5-16. Power Amp location ....................................................................................................................................... 5-28
Figure 5-17. Circuit board of the 50W Power Amp showing locations of jumpers, switches, connectors, potentiometers.5-29
Figure 5-18. Location of jumpers on Tx Filter, PC Board 107828-2 .................................................................................. 5-35
Figure 5-19. Location of jumpers on Tx Filter, PC Board 107828-1 .................................................................................. 5-36
Figure 5-20. Location of Jumpers on Line Board................................................................................................................ 5-38
Figure 5-21. Location of Jumpers on Rx Filter Board, showing jumper groupings ............................................................ 5-43
Figure 5-22. Location of Jumpers on RF Motherboard....................................................................................................... 5-44
Figure 7-1. Front View of RFL 9508 Analog Section........................................................................................................... 7-1
Figure 7-2. RF Chassis Diagram ........................................................................................................................................... 7-3
Figure 7-3. RFL 9508 Power Amplifier ................................................................................................................................ 7-5
Figure 7-4. Chassis configurations for RFL 9508D with 50W Amp and with 100W Amp .................................................. 7-7
Figure 7-5. Front View of Additional 3U Chassis for 100W Systems .................................................................................. 7-7