RF RFT-805D Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 8

RF RFT-805D Скачать руководство пользователя страница 4

3.2 First time set-up

When using the unit for the first time, you must first connect video and audio source to audio/video inputs
and then connect video output to monitor. After this you can continue set-up using on-screen menus.

To control the unit first slide front panel switch to ON position. When programming is ready, the front panel
switch must be slide to OFF position. This will prevent accidental changes to be made while controlling
other units

.

3.3 Set-up

To start set-up, press Menu key. Main Menu will be displayed.

Select “ Modulator Configuration”.

In Modulator menu can be selected:

-

Output channel from S2 to E69

-

DVB-T Constellation (QAM 64 is recommended)

-

DVB-T FEC 1/2, 2/3, 3/4, 5/6 or 7/8 (3/4 is recommended)

-

DVB-T Bandwidth 7 MHz or 8 MHz

-

Output Level attenuator 0...20 dB (20 is maximum output level)

-

Fine Tune of output frequency with 0,5 MHz steps

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fax. +358-2-736 6360, [email protected], www.rf-tuote.fi

«
...
2
3
4
5
6
...
»

Содержание RFT-805D









Отзывы:

Нет отзывов