RF RFT-805D Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 8

RF RFT-805D Скачать руководство пользователя страница 2

1. Purpose of use

RFT-805D is a digital modulator designed for a processing two audio and two video signals into one
COFDM (DVB-T) multiplex.

2. Installation

The connections and indications are shown in Fig 1.

1. Cable-TV S channel indicator led
2. Channel number ( CCIR)
3.Control switch to program channel in ON position. The switch must
be set to OFF (DOWN) position when programming is ready1.
4. IR detector
5. VIDEO/AUDIO outputs for monitoring
6. Audio IN (right)
7. Audio IN (left)
8. RGB IN (blue) or YPbPr (Pb)
9. RGB IN (green) or YPbPr (Y)
10. RGB IN (red) or YPbPr (Pr)
11. Video IN and SCART SYNCHORIZING IN
12. USB port for software update
13. S-Video IN
14. When signal led is orange, the unit is initialized. When signal led
is green, the outgoing stream is ready. Red led means overfull stream.
15. DC IN (only in stand-alone installation)
16. RF OUT + DC IN in RFT-800 system installation

RFT-805D can be mounted either to RFT-800 system (RFT-800 User Manual) or stand-alone. Do not
cover the air passage holes.

Signals from AUDIO/VIDEO source are fed to Audio/Video connectors (RCA female) or S VIDEO IN.

When RFT-805D is mounted for RFT-800 system, the power voltage is supplied through active output
combiner (RFC-808 or RFC-816). When RFT-805D is mounted stand-alone, power supply unit (RFP-
804 or RFP-808) must be mounted to the left side of RFT-805D due to the ventilation. DC connector

is

connected to left side of DC connector at the bottom of unit. You can loop-through DC from the right
side DC connector to next unit with the DC cable. Maximum four RFT-805D units in chain can be
supplied with one power supply (RFP-804) in stand-alone installation (max. two units with RFP-802).

When RFT-805D is mounted for RFT-800 system, cable to network is connected to active output
combiner (RFC-808 or RFC-816). When RFT-805D is mounted stand-alone, RF OUT is connected to
cable network.

VIDEO/AUDIO connectors (5.) are for monitoring the unit while programming.

NOTE! If video input is not connect, there are white stripes in video output due to the missing sync
pulse.

RF-Tuote Oy, Joensuunkatu 13, 24100 Salo, tel. +358-2736 6360, fax. +358-2-736 6360, [email protected], www.rf-tuote.fi

«
1
2
3
4
...
»

Содержание RFT-805D









Отзывы:

Нет отзывов