MAINSLINK-PRO
Page: 2
QS-MAINSLINKPRO-4
PATENT No 2564512
SWITCHING
LIVE
IN / OUT
N E N
L
Permanent
LIVE Supply
L
IV
E
IN
PERMANANT
SUPPLY
WDOG
MODE
MOM/LAT
L
2
(L
IV
E
O
U
T
N
/C
)
L
1
(L
IV
E
O
U
T
N
/O
)
Installation
Multiple System Operation
Each MAINSLINK-PRO system contains a unique identity so multiple systems can operate within the
same area without interfering with each other.
Connect the Supply to both units
Connect the permanent LIVE Feed and NEUTRAL supply.
Connect the Switched Input Lin
Connect the Switching Live input to Lin
When the Switched Live input (LIVE IN) is ‘LIVE’ the
LED
will illuminate, and the Lout at the other
MAINSLINK-PRO will then switch Live out.
Connecting the Switching Load Lout
Connect your LOAD to Lout
When the Switched Live Output (LOUT) is ‘LIVE’ the
Red
LIVE OUT LED will illuminate.
COMMS LED
ON
One Flash
Two Flashes
3 Flashes
Operation
Status
RF Link OK
Out of range
Powered
But unpaired
In Pairing Mode
Description
System
operating OK
No RF connection
to other
MAINSLINK-PRO
Waiting to be
paired to another
MAINSLINK-PRO
Actively sending an RF
‘Please Pair message’
Indicates
Input is LIVE
Coms Indicates RF
Link Status
Indicates
Output is
LIVE
MAINSLINK-PRO
Page: 3
QS-MAINSLINKPRO-4
PATENT No 2564512
SWITCHING
LIVE
IN / OUT
PERMANANT
SUPPLY
WDOG
MODE
MOM/LAT
Jumper Link Setting
There are three Jumper Links which may be used to configure the following:
Link
Open
Fitted
WDOG
Watchdog OFF
Watchdog Active
MODE
LORA Mode 3
LORA Mode 7
MOM/LAT
Not Used
WDOG - WATCHDOG
This provides improved reliability and security useful in with electrically noisy Loads.
When the WDOG link is fitted each MAINSLINKPRO automatically sends a background watchdog RF signal
and expects to receive a corresponding WDOG signal from its partner.
If the WDOG signal is not received within 90seconds, the output will drop out and comms LED will flash.
MODE
LORA Mode 3
—
Faster operation shorter range (Line of sight upto 3Km/500m in buildings)
LORA Mode 7
—
Long range (Line of sight up to 5Km/1Km in buildings)
NOTE! In this mode a transmitted signal can take 2 seconds to trigger the receiver.
MOM/LAT -
Must be left OPEN for correct operation.
1. Apply a 230Vac supply to the first MAINSLINK-PRO
2. Briefly place a magnet across enclosure (Right side as shown) to
activate the internal reed switch.
3. The GREEN comms LED will flash 3 times to show in Pairing Mode
Advanced Operation
—
Pairing together two MAINSLINK-PROs
NOTE: This system does not require pairing, they are supplied ready to operate!
Erasing a MAINSLINK-PRO
A
B
4. Apply 230Vac to the second MAINSLINK-PRO
5. Briefly place a magnet across enclosure (Right Side as shown) to
activate the internal reed switch.
6. The GREEN comms LED will flash 3 times to show in Pairing Mode
7. The two MAINSLINK-PRO units which will now auto pair together
(allow 30 secs -Green Comms LED will stay on.)
To erase the system hold a magnet beside the Right Side of the
enclosure for 10 seconds as shown.
Repeat this process on both units to erase system.
