background image

Page No 4 of 56 Reznor, RHC21 4000 Installation EN May 2021 D301334 Issue 0

In instances where copper pipework is to 
be used for all or part of a gas pipework 
installation, including short length final 
connections then we advise that installers 
consult with the gas supplier or provider and 
satisfy themselves what additional precautions 
may be necessary.

Improper installation, adjustment, 
alteration, service, or maintenance 
can cause property damage, 
injury, or death. Read the 
installation, operation, and 
maintenance instructions 
thoroughly before installing or 
servicing this equipment.

Gas-fired appliances are not designed for 
use in hazardous atmospheres containing 
flammable vapours or combustible dust, 
in atmospheres containing chlorinated or 
halogenated hydrocarbons or in applications 
with airborne silicone substances.
Any reference made to Laws, Standards, 
Directives, Codes of Practice or other 
recommendations governing the application 
and installation of heating appliances and 
which may be referred to in Brochures, 
Specifications, Quotations, and Installation, 
Operation and Maintenance manuals is done 
so for information and guidance purposes only 
and should only be considered valid at the 
time of the publication.
The manufacturer cannot be held responsible 
from any matters arising from the revision 
to or introduction of new  Laws, Standards, 
Directives, Codes of Practice or other 
recommendations.
The temperature in the controls section of the 
unit must never be less than -10°C otherwise 
damage could occur to the sealing elements of 
the gas valve and to the electrical components. 
The electrical isolator should only be used in an 
emergency and should not be used for closing 
down the main burner, as it switches off the 
fan prematurely and may damage the heat 
exchanger, invalidating the warranty.

Important notice to 
installers 

Before installation, carefully read these 
instructions and follow the processes explained 
by the manufacturer. These instructions are 
only valid for appliances designed to operate in 
Europe. If the country code and gas category 
on the appliance data label does not match 
the country of installation or the country codes 
and gas categories as shown in this instruction 
manual, it will be necessary to contact the 
distributor or manufacturer to provide the 
necessary information for the modification of 
the appliance to the conditions of use for the 
country of installation.
Installing, commissioning, testing, 
programming and maintenance of these 
products must only be carried out by suitably 
qualified and trained technicians and in full 
compliance with all applicable regulations and 
current best practices. 
Check if the appliance as described on the 
packaging label is in accordance with the 
correct type and model as specified on the 
data plate and complies with your customer 
order.
Check that the temperature ranges given 
and those of the location match. The 
appliance must be powered with a voltage 
corresponding to the value shown on the 
rating plate. 
These units must be installed in accordance 
with the rules in force and local regulations / 
legislation as appropriate plus all local building 
codes. Installers should satisfy themselves that 
the gas pipework installation is carried out in 
accordance with all current legislation, Codes 
of Practice and recommendations. 
Additionally it may be necessary to protect 
the gas valves which form part of the heater 
or burner assembly from potential pipe 
contamination particularly, but not exclusively, 
where copper gas pipework is used. 

Содержание RHC21 4000

























































Отзывы: