manualshive.com logo in svg

Rexnord Planetgear 7000, Руководство пользователя

Поделиться
Скачать
Rexnord Planetgear 7000 Скачать руководство пользователя страница 21

Owners Manual • Rexnord

®

 Planetgear

™

 7000 Speed Reducers

(Page 21 of 33)

 Size Mercury/Mars

158-110     

10/21 (Supersedes 01/15)

 rexnord.com

© Rexnord Corporation. All Rights Reserved. 

Contact us — visit 

rexnord.com/contact 

7.  Carefully set the housing, outboard side face down, 

onto the outboard bearings.

8.  While rotating the housing on bearings, apply clean oil 

to the bearings.

9.  Place the inboard bearing cone squarely on the inboard 

end of  the shaft with the smaller diameter of  the 

bearing facing the outboard. Reference 

Figure 6.3.5.4

.

OUTBOARD

BEARING CONE

INBOARD 

BEARING CONE

INBOARD END OF SHAFT

Figure 6.3.5.4  Placing Inboard Bearing Cone onto Shaft

10. With an arbor press or a hydraulic press carefully push 

bearing cone. When bearings begin to approach the 

bearing cup, apply clean oil to inboard bearings.

NOTE

: DO NOT push on bearing rollers or bearing cage. 

Reference 

Figure 6.3.5.2

.

11. Press inboard bearing until it touches the surface of  

the bearing cup.

NOTE

: Do not over push bearings into cup. This might 

cause the bearings to Brinell the cup.

NOTE

: An indication when the inboard bearing is fully 

seated is when the hub will not rotate on the shaft 

freely.

12. Clean and place the bearing spacer onto the shaft.
13. Clean locknut. Place it with the grooved side down (or 

groove towards bearings) and thread on locknut until it 

is unable to rotate.

14. Mark the location of  the locknut.
15. Loosen locknut approximately 5/16" (8 mm) from 

original mark.

16. Tighten set screw on locknut.
17. Hold housing on its’ side, and with a blunt instrument, 

rap on the inboard side of  shaft. Reference 

Figure 

6.3.5.5

.

BEARING 

SPACER

LOCKNUT

Figure 6.3.5.5  Final Assembly of Input Shaft Housing

NOTE

: Shaft should be able to rotate freely at this time. 

Replace seals after bearing clearance has been 

established.

18. Reference Axial Bearing Clearance, 

Section 6.4

 for 

proper bearing endplay.

6.3.6 ASSEMBLING OUTPUT SHAFT 

ASSEMBLY

1.  Clean bearing surface on shaft.
2.  Make sure bearing cups are clean and installed 

properly in housing. Reference 

Section 6.3.4

.

3.  Set shaft on end with the spline end of  the shaft facing 

up.

CAUTION

:  Pilot assembly so that it will not fall over.

4.  Place the outboard bearing cone squarely on the 

inboard end of  the shaft with the smaller diameter of  

the bearing facing inboard. Reference 

Figure 6.3.6.1

.

OUTBOARD

BEARING CONE

SHAFT

PILOT

INBOARD END OF SHAFT

Figure 6.3.6.1 Placing Outboard Bearing Cone onto Shaft

5.  With an arbor press or a hydraulic press carefully push 

bearing cone until it bottoms on shaft shoulder.

NOTE

: DO NOT push on bearing rollers or bearing cage. 

Reference 

Figure 6.3.6.2

 for location.

BEARING

ROLLERS

BEARING

CONE

BEARING

CAGE

Figure 6.3.6.2  Location of Bearing Components

6.  With a 0.001" or 0.040 mm feeler gage, make sure that 

there is no gap between the shaft shoulder and the 

bearing cone to insure proper cone seating. Reference 

Figure 6.3.6.3

 next page.

Содержание Planetgear 7000


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды