Rexnord Falk SteelfIex T10 Series, Установка и обслуживание

Страница: 5 / 6

Falk Steelflex Couplings • Installation & Maintenance
Type T10 • Sizes 1150 – 1260 & 150 – 260 (Page 5 of 6)
Rexnord
428-112
5555 S. Moorland Rd., New Berlin, WI 53151-7953 USA March 2014
Telephone: 262-796-4060 Fax: 262-796-4060 web: www.rexnord.com Supersedes 4-05
TYPE T COUPLING INSTALLATION &
ALIGNMENT DATA
Maximum life and minimum maintenance for the coupling
and connected machinery will result if couplings are
accurately aligned. Coupling life expectancy between
initial alignment and maximum operating limits is a function
of load, speed and lubrication.
Values may be combined for an installation or operating
condition.
Example: 1180T max. operating misalignment is .030”
parallel plus .089” angular.
NOTE: For applications requiring greater misalignment,
refer application details to the Factory.
Angular misalignment is dimension X minus Y as illustrated
below.
Parallel misalignment is distance P between the hub center
lines as illustrated below.
End float (with zero angular and parallel misalignment)
is the axial movement of the hubs(s) within the cover(s)
measured from “O” gap.
GAP
Y
X
F F
ANGULAR MISALIGNMENT
P
P
PARALLEL OFFSET MISALIGNMENT
END FLOAT
TABLE 1 — Misalignment and End Float
CPLG
SIZE
Installation Limits Operating Limits
Cover
Fastener
Torque
Values
Allow
Speed
(rpm)
Lube Wt
Parallel
Offset-P
Angular
(x-y)
Normal Gap
± 10%
Parallel
Offset-P
Angular
(x-y)
End Float
Physical
Limit
(Min) 2 x F
Max
Inch
Max
mm
Max
Inch
Max
mm
Inch mm
Max
Inch
Max
mm
Max
Inch
Max
mm
Inch mm lb-in Nm lb kg
1150T .012 .305 .016 .406 .250 6 .024 .610 .062 1.57 .620 15.7 650 73.4 1500 4.3 1.95
1160T .012 .305 .018 .457 .250 6 .024 .610 .070 1.79 .640 16.3 650 73.4 1350 6.2 2.81
1170T .012 .305 .020 .508 .250 6 .024 .610 .079 2.01 .617 15.7 1300 146.9 1225 7.7 3.49
1180T .015 .381 .022 .559 .250 6 .030 .762 .089 2.26 .717 18.2 1300 146.9 1100 8.3 3.76
1190T .015 .381 .024 .610 .250 6 .030 .762 .097 2.46 .620 15.7 1300 146.9 1050 9.7 4.40
1200T .015 .381 .027 .686 .250 6 .030 .762 .107 2.72 .620 15.7 2300 259.9 900 12.4 5.62
1210T .018 .457 .029 .737 .500 13 .036 .914 .118 3.00 1.02 25.9 2300 259.9 820 23.2 10.5
1220T .018 .457 .032 .813 .500 13 .036 .914 .129 3.28 1.15 29.2 3580 404.5 730 35.4 16.1
1230T .019 .483 .035 .889 .500 13 .038 .965 .142 3.61 1.12 28.4 3580 404.5 680 53.0 24.0
1240T .019 .483 .038 .965 .500 13 .038 .965 .154 3.91 1.12 28.4 5350 604.5 630 74.5 33.8
1250T .020 .508 .042 1.07 .500 13 .040 1.02 .169 4.29 1.12 28.4 5350 604.5 580 110.5 50.1
1260T .020 .508 .046 1.17 .500 13 .040 1.02 .183 4.64 1.01 25.7 5350 604.5 540 148.1 67.2