REVENTON INSPIRO, Техническая документация инструкция

Страница: 8 / 13

and then use MODE button to go to the next positions:
Controlling
Settings - press SET button for 6 seconds to enter the edition mode
ź
Clock – while in the clock setting mode, press SET button and use UP
and DOWN arrows to set the hour. Then press again MODE button
to set the minutes in a similar way. To confirm the set time press SET button.
ź
Day – while in the day of the week mode, press SET button and use UP
and DOWN arrows to set the correct one. To confirm the set day press SET
button.
If the period is active, press MODE button to move to the end time of the period
(using UP and DOWN arrows and MODE button to go from hour to minute
or vice versa). To confirm the set start time of the period press SET button. Repeat
the above steps until the start times for all required periods are set.
Then press SET key again to save the set schedule.
If the period is active, press MODE button to move to the start time of the period
(using UP and DOWN arrows and MODE button to go from hour to minute
ź
Weekly timer on – while in the weekly switch settings mode, press SET button
and then by pressing SET key select correct day of the week and period 1 or 2
(two periods per day can be programmed). After selecting the day, press POWER
ON / OFF button to activate / deactivate the start time of the period for the day.
ź
Weekly timer off – while in the weekly switch settings mode, press SET button
and then by pressing SET key select correct day of the week and period 1 or 2
(two periods per day can be programmed). After selecting the day, press POWER
ON / OFF button to activate / deactivate the end time of the period for the day.
or vice versa). To confirm the set end time of the period press SET button. Repeat
the above steps until the end times for all required periods are set. Then press
SET key again to save the set schedule.
Error code – press SET buton to display the error code.
to value 1 (see point 6.3).
to set the required supply air temperature from the range 10 - 25°C.
to previous settings when the humidity level falls below the permissible value.
in the humidity sensor mode, use UP / DOWN arrows to set the maximum
permissible relative humidity (within the range of 45 - 90%), after which the unit
starts to work automatically at the highest speed. The device will return
ATTENTION! If humidity sensor is connected, remember to change
Setting humidity sensor (available only if humidity sensor is connected) –
the switching circuit 3 to ON position (see point 6.6).
Setting supply air temperature (available only if electric heater is connected
in the supply air side) –
in the TA mode, use UP / DOWN arrows
ATTENTION! If heater is connected, remember to change parameter no. 1
ź
If OA temperature is > -15°C, but FR temperature is < -1°C, preheater turns
ATTENTION! In the ON mode standard RA temperature sensor is deactivated
because its function is taken over by the humidity sensor. For this reason
ź
If OA temperature is < -15°C the preaheater turns on for 50 minutes
Switching circuit 1 – allows you to change the defrosting mode. It is set to OFF
by deafult, i. e. defrosting by using return air. Changing the position to ON
and the fans turn off for 10 minutes (after this time they turn on again)
Switching circuit 3 – in the OFF mode, the unit works according to the CO
2
sensor (if connected) and in the ON mode it reacts on the CO
2
sensor signal
The dial switch is located on the controller (see wiring diagram in point 7)
on for 10 minutes
6.6 DIAL SWITCH
and allows the controller to adapt to the user's requirements. It consists of four
two-state switching circuit, which correspond to:
ź
If the preheater is turned on and OA temperature is > 25 °C, the preheater turns
off for 5 minutes; if such situation repeats 3 times in a row, the preheater turns off
Switching circuit 2 – allows to inactivate the bypass function (both automatic
and manual bypass using dedicated circuit) - to do this, switch the system from
OFF (default) to ON position.
is a signal for the controller, a preheater on the outside air side has been
connected and the possible defrosting process will be carried out using it:
ź
If the preheater is turned on and FR temperature is still < -1°C, the fans turn
and / or the relative humidity (if connected).
if the circuit 3 is in ON position without a humidity sensor connected, an error
code E3 will be displayed.
Switching circuit 4 – in the OFF mode value of baud rate is 4800, while in the ON
mode it is 9600
off for 50 minutes
Code
E1
E2
E3
E4
E5
E6
E7
E8
Error
fresh air temperature sensor (OA) error
EEPROM memory error
return air temperature sensor (RA) error
exhaust air temperature sensor (FR) error
communication error
supply air temperature sensor (SA) error
exhaust fan error
supply fan error