English
English
16
17
6 TRIM ADJUSTMENT oF ThE CoNTRoL
The correct trim is a basic requirement for fault-free flying behaviour of the
quadrocopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the quadrocopter approximately 0.5 to 1 metre in altitude.
6A If the quadrocopter moves by itself slowly or quickly to the left or right …
Press the trim control for banking incrementally in the opposite direction.
6B If the quadrocopter moves by itself slowly or quickly around its own axis …
Press the trim control for rotation incrementally in the opposite direction.
6C If the quadrocopter moves by itself slowly or quickly forwards or
backwards …
Press the trim control for forward and backwards flight incrementally in the opposite
direction.
4 ChARGING ThE QUADRoCopTER
Attention:
The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Unplug quadrocopter from the battery, switch off the remote control and insert the
charter into an active USB connection. The control LED on the charger illuminates red
(4A)
.
• Remove the battery from the battery compartment (do not hold by the cable!)
(4B)
.
• Now plug the battery into the cable of the USB charger. Pay attention to the polarity
in the process. Please do not use force. The red LED on the charger illuminates when
the charging process begins.
• The charging process lasts approx. 60 minutes and must be continuously monitored.
The red LED on the USB charger goes out when the charging process is finished.
• Disconnect the battery from the charging unit and disconnect the charging unit from
the USB port after the charging is completed
(4C)
.
5 START pREpARATIoN
The thrust controller (the left controller on the remote control) must point down before
being switched on
(5A)
. Then move the ON/OFF switch
(5B)
on the remote control
to "ON" and the Power LED will begin to blink
(5C)
. Connect the battery cable using
the connection cable
(5D)
. The LED on the quadrocopter now starts to blink. Place
the quadrocopter on the ground so that the tail points toward you with the two red
propellers in the rear
(5E)
. The quadrocopter needs around 5-10 seconds to initialise
the gyro and to establish the connection to the remote control. As soon as the LED on
the quadrocopter lights up green permanently, the connection for the remote control
has been established.
Warning!
Be sure to place the quadrocopter on a level surface – the control electronics
aligns its neutral position to the surface!
3 INSERTING BATTERIES (REMoTE CoNTRoL)
3A
Unscrew the screw
and remove the
cover
3C
Fit the cover on
again and screw it
in place.
3B
Insert 4 x 1.5 V AA batteries
and pay attention to the
polarity, as shown in the
battery compartment.
2 REMoTE CoNTRoL
2A
Antenna
2B
Power LED
2C
Trim control for forward and backward
flight
2D
Controller for forward and backward
flight as well as banking
2E
Trim control for banking
2F
Button for the looping function
2G
Button for flight speed
2H
Display
2I
Trim control for rotation
2J
Controller for thrust and rotation
2K
ON/OFF switch
1A
Bonnet
1B
Front propeller (white)
1C
Rear propeller (red)
1D
Battery compartment
1E
Battery connection cable
1F
Battery plug connector
1 QUADRoCopTER
The quadrocopter can fly for approx. 6-8 minutes after a charge time of
approx. 60 minutes.
Warning notice:
The LiPo battery can become warmer during charging. If it should
become hot and/or changes to the surface begin to appear, immediately discontinue
the charging process!
