REV Robotics MINI BOT Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 37

background image

The best way to use screws and bolts to secure a bracket to the extrusion,

is by “pre-loading” loading them.This simply means that before even bringing the bracket near

the extrusion, we insert all the screws that will be going through the extrusion, onto the bracket.

3. Pre-loading

Tip #3: PRE-LOADING

1) Make sure you know which side of your

item will be facing the extrusion.

2) Thread the screws onto your piece with the

screw heads on the extrusion facing side.

3) Just barely “finger start” the

nuts onto the backs of the

screws. It should be loose.

4) Do NOT thread all the way.

Just enough so that the nut hangs

on to the end.

5) Thread the screw heads of your

piece onto the extrusion. Slight

wiggling will help the screws line up.

6) You can now slide along the extrusion.

7) Once piece is placed, tighten the screws.

screw head

space/

wiggle room

3

«
...
5
6
7
8
9
...
»

Содержание MINI BOT






































Отзывы:

Нет отзывов

Похожие инструкции для MINI BOT

Бренд: Kondo Страницы: 69

Бренд: Sybo Tech Singapore Страницы: 19

dynamixel AX-12

Бренд: Robotis Страницы: 38

Бренд: Robotnik Страницы: 33

Бренд: OSOYOO Страницы: 86

Бренд: Giochi Preziosi Страницы: 48

Бренд: KamiBot Страницы: 9

Бренд: LinkSprite Страницы: 35

Бренд: Raspberry Pi Страницы: 20

Бренд: Makeblock Страницы: 22

Бренд: Dreaming Robots Страницы: 8

Бренд: EastPoint Страницы: 16

Бренд: Motoman Страницы: 64

Бренд: Motoman Страницы: 73

GEV TS 121650 AR-2

Бренд: Getinge Страницы: 59

Edison Robot V2.0

Бренд: Edison Страницы: 16

Бренд: Edison Страницы: 17

Бренд: Edison Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды