Product introduction
Thanks for using Retekess wireless calling system, it adopts FSK wireless technology . The system
consists of 1 keyboard transmitter and 10 coaster pagers, the receiver supports 1999-channel
extensions. Each pager is rechargeable and labeled with a number, in standby status, it is plugged into
the charging slots, while the guest places an order, he(she) will be dispatched one receiver with a
number, when the order is ready, the waiter will press the keypad to call the corresponding number, the
guest will get it through the buzzer/vibration/LED indications.
The calling system greatly improves the work efficiency and avoid the guest waiting in a long queue. It
is widely used in queuing occasions such as food court, logistics centers, clinics and so on.
Technical data
Working frequency
Standby current
Standby Time
Receive sensitivity
Battery capacity
Modulation technology
Dimmension
DC 3.7V
(Rechargeable battery)
433.92MHz
2mA
≈48 Hour
-106DB
250mAh
FSK
Φ105*16mm
Working voltage
Receiver
Power input
Working frequency
Transmit Power
Modulation technology
Dimmension
DC5V/3A
433.92MHz
＜
0.5W
FSK
170*85*41mm
Transmitting host
◆
Product description
1.Instructions for the use of the keyboard transmitter
Install the antenna first, put the keyboard protective film to protect the keyboard from water and dust,
and then connect the special power adapter, the power indicator light is on, and the screen is
displayed.
●Standby interface:
Packing List
Number
1
2
3
4
Quantity
1
1
1
1
Name
Transmitting host
Receiver
Power adaptor
Antenna
Quantity
1
10
2
1
Number
5
6
7
8
Name
Charging base
Serial port line
Serial port to USB line
User manual
Number area
：
You can enter the call number (from 1 to 1999), if you do not need to sent extra
message, press “SEND” directly to call the receiver.
Text area
：
You can enter the message (the default message can be set through the
software),and when the number and content are set, you can press the SEND key to call the receiver.
●
Keyboard description
The button layout is shown in the picture.
：
ESC: Delete all numbers and message and return it to the standby interface.
Words: Invoke the stored messages or settings and insert them into the call contents.
Insert: Change the input status to add or overwrite, the default is to add.
Delete: Delete the character where the cursor is located.
Arrows: Move the cursor up,down,left and right.
0-9:In the number input area, only numeric works, and in the text input area, both the characters and
punctuation marks all work. For example, if you press key 3 continuously, the 3, w, x, y loops are
displayed.
2
、
Instructions for the use of pager
●Power on
：
The pager is powered on automatically while putting it in the charging base.
●Power off
：
Remove the pager from the charging base, then press the button on the back of the pager
immediately, and the “OFF”will diplay on the digital tube.
●The pager could be called only when the pager is not on the charging base.
●When the pager is removing from the charging base, it will be detected automatically within
seconds.The self-test mode (LED, buzzer and vibration) is same as the pagers actual reminder mode.
●Reminder mode: vibration, buzzer beep and flash can be freely combined.
●There are two red lights on both sides of the digital tube when the power of the pager is low,also the
digital tube will show the number and LOW alternately,you need to put the pager back to the charging
base.
●When the pager is being charged, the red light will be on, and when it is fully charged, the red light will
go out.
3
、
Instructions for the use of the charging base
The charging base cannot be connected with a non-matching power supply.
◆
Setting description
1
、
Pairing
In the standby mode, enter the number in the Number Area, press the drop-down button "
Ⅴ
" to the Text
Area, then press the WORDS button, and then press the drop-down button "
Ⅴ
" again to enter into the
setting mode, “STUDYCAPCODE” will be shown in the screen display, remove the pager from the
charging base and press the button on the pager at the same time, then press the SEND button on the
keyboard (this operation must be completed within 10s, otherwise it needs to be re-operated).
Brief description: Enter the number to be paired →"
Ⅴ
" →”Words”→ "
Ⅴ
"
（
Display“STUDYCAPCODE”
）
→ Press the button on the pager →"SEND"→ Done
2
、
Function setting
：
The functions could be set through the keyboard transmitter while the pagers are on the charging base
(standby mode).
Operation steps
：
In the standby state, press the drop-down button "
Ⅴ
" to move the cursor to the Text Area, press
the”WORDS” button, then select the desired function through the up "Λ"/the drop-down key "
Ⅴ
", then
press the “SEND” button on the keyboard, and the pager displays "SET" means the setting is
completed.
The following features are supported
:
●STUDYCAPCODE
●SET FLASH LED ENABLE/SET FLASH LED DISABLE
●SET BEEP ENABLE/SET BEEP DISABLE
●SET VIBRATE ENABLE/SET VIBRATE DISABLE
●SET REMIND VOICE ENABLE/ SET REMIND VOICE DISABLE
1
2
