Summary
Thanks for choosing this wireless calling receiver.The receiver host adopts RF wireless and learning code technology.It can
easlly pair up to 999 channels of wireless calling transmitters and 10 manager remote controller.The receiver host uses
advanced industrial mlcro processor and high sensitivity superheterodyne receiving technology which make the products very
stable.
At same time,the wireless calling receiver host has advanced number speaker function,it can clearly read the number ,function
and so on and compatlbly for different working mode,suitable for different places.
The wireless calling system has millions of different code which can be paired easily and freely.And it widely used in restaurant,
café,bar,tea shop,KTV,bank,office,factory,hotel,hospital and so on.
Technical data
Woking frequency:433MHz
Woking voltage:DC12/2A
Woking current:
＜
650mA
Standby current:
＜
200mA
Sensitivity:-110dBm
Button Function
UP/DOWN: Up / down move function
SET
：
Long press and hold “SET” button 3 seconds to enter main setting menu
，
short
press “SET” button to enter submenu or confirmation. If there is no operation for more
than 1 minute, the system will automatically return to the standby interface.
BACK
：
Return or exit.
DEL
：
Delete settings or call information.
USB
：
Connect the interface with the computer when using the host computer software
DC12V
：
Power input.
Software: Reserved function extension, which is not defined for the time being.
Audio out
：
Audio output.
SYSTEM SETTING
1.F01: Number Registration
•Add transmitter
Long press and hold “SET” button 3seconds to enter main setting menu, then press “UP/DOWN” button to select menu F01,
short press “SET” button to enter F01 submenu, the display shows “001”, then trigger the transmitter to program it to be Number
1 transmitter (after program, the number will be increased by 1 automatically, which can only be realized on an individual bit,
and must be manually adjusted on 10 or 100 digits.). The speaker will sound “successfully registration”. Short press “BACK”
button to previous menu or press “BACK” button twice to exit to standby.
Note: When a number has been learned, it flashes and other transmitters can no longer learn unless short press "DEL" button
to delete the number.
If a number is not learned, it is always on and does not flash.
•
Delete a transmitter separately
Long press and hold “SET” button 3 seconds to enter main setting menu, then press “UP/DOWN” button to select menu F01,
short press “SET” button to enter F01 submenu, the display shows “001”
，
press “UP/DOWN” button to select one of the
number which want to delete, then press “DEL” button at the right side of the display receiver. If the number was programmed,
the number will flicker; If the number was not programmed before, the number would not flicker. After delete the number, it would
not flicker and sounds “Delete Successfully”.
To delete all transmitters quickly, please use F08 restore factory default (submenu 1 or 2).
2.F02: Remote Control Registration
Long press and hold “SET” button 3 seconds to enter main setting menu, then press “UP/DOWN” button to select menu F02
，
short press “SET” button to enter F02 submenu, the display shows “0” (Default), then press relevant remote control
，
The speaker will sound “successfully registration”. After program Manager Remote Control, the user can use programmed
remote control to setup the display receiver remotely.
Note:Support up to 10 management remote controls
3.F03: Prompt Music
Long press and hold “SET” button 3 seconds to enter main setting menu, then press “UP/DOWN” button to select menu F03
，
short press “SET” button to enter F03 submenu, the display shows “1” (Default), then press “UP/DOWN” to select prompt music
mode, and then short press “SET” button to confirm:
0: Speaking Number only
1: Ding-Dong + Speaking Number (Default);
2: Airport Broadcast Voice only;
3: Mute (no voice) ;
After program, press “BACK” button to previous menu or press “BACK” button twice to exit to standby.
4.F04: Volume
Long press and hold “SET” button 3 seconds to enter main setting menu, then press “UP/DOWN” button to select menu F04
，
short press “SET” button to enter F04 submenu, the display shows “6” (Default), then press “UP/DOWN” to setup relevant
volume from 1 (lowest) to 6 (highest). Short press “SET” button to confirm. After program, press “BACK” button to previous
menu or press “BACK” button twice to exit to standby.
UP
DOWN
SET
BACK
Software
Audio out
USB
DC12V
DEL
1
