manualshive.com logo in svg

Repotec WD-5714 H, Руководство пользователя

Поделиться
Скачать
Repotec WD-5714 H Скачать руководство пользователя страница 12

 

 
a.

 

DHCP Server 

DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses 
when a device is booting up and request an IP address to be logged on to the network. That 
device must be set as a DHCP client to obtain the IP address automatically. By default, the 
DHCP Server is enabled. The DHCP address pool contains the range of the IP address that 
will automatically be assigned to the clients on the network. 
 

Item

Description 

Starting IP 
Address 

The starting IP address for the DHCP server's IP assignment. 

IP Pool Count 

The max user pool size. 

Lease Time 

The length of time for the IP lease. 

 
b.

 

DHCP Relay 

A DHCP relay is a computer that forwards DHCP data between computers that request IP 
addresses and the DHCP server that assigns the addresses. Each of the device's interfaces can 
be configured as a DHCP relay. If it is enable, the DHCP requests from local PCs will 
forward to the DHCP server runs on WAN side. To have this function working properly, 
please run on router mode only, disable the DHCP server on the LAN port, and make sure the 
routing table has the correct routing entry. 
 

Item

Description 

DHCP Server 
IP for relay 
agent 

The DHCP server IP Address runs on WAN side. 

 

Содержание WD-5714 H





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды