background image

3

WARNING: THIS APPARATUS MUST BE SECURELY ATTACHED TO A WALL IN 

ACCORDANCE WITH THESE INSTRUCTIONS. FAILURE TO DO SO MAY RESULT IN INJURY.

Do not stand the loudspeaker upright or lay it on its side on the floor.

 

To ensure proper air movement for the cooling of the amplifier module, we recommend a minimum of 2 to 3 feet of clearance in front of the loudspeaker 

and 3 to 4 inches of clearance from the other cabinet surfaces. 

Mounting loudspeakers is a task for experienced professionals. Improperly installed loudspeakers can result in property damage, personal injury, death 

and /or liability for the installer.

These instructions assume that the installer will exercise good judgement in selecting the mounting area and hardware. If you have any doubts about the 

integrity of the mounting structure or are not sure about the proper hardware to use, consult a structural and or hardware specialist.

This loudspeaker is intended to be securely mounted using MultiMount EEM-W-WALL-IC7-II and is not intended to be free-standing. 

This mounting instruction supersedes mounting instructions provided with the MultiMount universal mounting kit. 

This loudspeaker has not been evaluated for safety requirements using other mounting kits.

The MultiMount EEM-W-WALL-IC7-II comes fully assembled and includes the following components.

 

1 - Wall Mounting Plate

 

2 - Loudspeaker Brackets

 

1 - Swivel Adapter

Tools Required

 Drill

 

Mounting hardware appropriate for the wall

 

Metric Socket Set or Wrench Set

MOUNTING NOTE

To ensure proper air movement for the coling of the 

amplifier module, we recommend 

a minimum of  2 to 3 feet of clearance in front. 

Wall Mounting Instructions

Introduction

Congratulations On your purchase of an Iconyx IC7-II self powered or ICX7-II externally powered loudspaker array It was designed to give you years of 

trouble free listening 

pleasure. We hope you enjoy it.

YourLoudspeaker system was carefully tested and inspected before leaving our factory and should have arrived in perfect condition. Please inspect it 

and its shipping carton for any noticeable damage and if any damage is found, immediately notify the shipping company. Only you, the consignee, may 

institute a  claim with the carrier for damage done during shipment. Be sure to save all shipping cartons and material for the carrier’s instection. 

Содержание Iconyx ICX7-II









Отзывы: