Mounting on the rear side of the TV
• Attach the holder with the mounting tap to one of the VESA mounting points on the rear of the
TV. Use a fitting screw and washer from the enclosed mounting material.
• Note here the max. screw length for the VESA mounting point, which different and subject to the
type of TV set (see manual of your TV set). If needed, use the enclosed spacer sleeves. If you do
not find a screw that fits among the material supplied, please buy a proper screw from a local
dealer.
Mounting on a TV wall mount
• Attach the holder with the mounting tap to a free drill hole on the TV wall mount as shown in the
picture.
Wall Mount
$SSOH
79
• Define the position of the holder at the mounting site.
• Use the holder as a template and mark the the required holes on the mounting surface.
• Drill the required holes and insert suitable dowels into the drilled holes (enclosed or special wall
plugs).
• Screw the holder tight as shown in the image. Use the enclosed screws or screws purchased
from your dealer that are suitable for the mounting surface.
Connect your Apple TV/Airport, power on and place it in the holder which you have previously
installed.
But before you place your Apple TV/Airport into the holder you should make sure that
you have downloaded and installed the required software apps for your device that
controls the Apple TV/Airport.
Maintenance and cleaning
Please use a soft, dry, clean cloth for cleaning.
Do not use aggressive detergents as these can cause discolouration of the case.
Technical data
Suitable for .............................................................Apple TV 2. and 3. Generation
..................................................................................
Apple Airport Express 2. Generation
Dimensions.............................................................106 x 127 x 30 mm
Mounting hole spacing for wall mount..............66 mm
Weight .....................................................................approx. 80 g
G
Operating instructions
Holder for Apple TV/Airport black
Item no. 1340795
Intended use
The product for mounting an Apple TV/AirPort Express on rear sides of TVs, TV wall brackets or
on a wall.
Any use other than that described above will lead to the damage of this product. It also carries
risks such as damage to the TV set, the Apple device to be attached, damage to furniture, etc.
No part of the product may be modified or altered.
The safety instructions must be observed at all times.
This product complies with the applicable national and European requirements. All names of com-
panies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• Holder for Apple TV/Airport Express
• Mounting material
• Operating instructions
Explanation of symbols
The exclamation mark indicates important information in these operating instructions.
The “arrow” symbol points to special tips and operating information.
Safety instructions
Read first the entire operating manual carefully; it contains important information
about the installation.
Damage due to not following these operating instructions will void the warranty! We
do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions! In such cases, the warranty will be
null and void!
• This product is not a toy. Keep the device out of the reach of children.
• Do not leave packaging material carelessly lying around. It may become a dangerous
plaything for children.
• Check the desired installation site for a proper fixture for the holder before you start
with the installation.
• Lay all cables of the Apple TV/AirPort Express so that they don’t get pinched or
kinked.
• In case of doubt, do not perform the installation yourself. Have an expert carry out
the installation.
Assembly
Use installation materials (screws, dowels, etc.) for a wall mount that are suitable for
the material the wall is made of (e.g. concrete). The dowel screws enclosed are used
exclusively for solid walls. Special wall plugs and screws are not included with the
holder and must be purchased separately, depending on the material of the wall.
Plan the mounting site carefully, so that the holder is located at the desired location
(height and position) after the installation is complete. Consider also the position of
the cable connection here.
Pay attention when drilling and tightening the screws that no cable or pipes in the
wall are damaged. Inadvertently drilling through electric cables causes the life-thre-
atening danger of an electric shock!
Pay special attention to your own safety when using electric tools (e.g. a drill). Follow
the safety instructions in the relevant instructions.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
