Before drilling the attachment holes, make sure that the electric cables, brake lines,
the fuel tank or similar systems will not be damaged.
When using tools for mounting your device, observe the tools manufacturers’ safety
instructions.
When installing the lamp, take into consideration the risks that can arise from devices
being torn away in the event of an accident. Therefore, fasten each part securely and in
a location where it will not pose a risk to passengers.
• Look for a suitable installation site.
• Remove the annular orifice from the housing.
• At the installation site, mark the location of the holes for the attachment screws and the location
of one hole for the cable exit under the cable duct. Use the lamp itself as a template for the at-
tachment holes.
• Drill the holes for the attachment screws (diameter: 2 mm) and the cable duct (diameter: 10 mm).
• Attach the lamp with the provided screws or other screws suitable for the mounting face.
• Then replace the annular orifice on the lamp housing.
Connecting the Power Supply
The electric connection should always be carried out by a specialist.
To avoid short circuits and any resulting damage to the device, the negative terminal
(chassis) of the vehicle battery has to be disconnected first.
Before reconnecting the negative terminal to the battery, ensure that the lamp has
been completely connected.
Only use a volt meter, or a diode test lamp, to check the voltage of the vehicle system
leads, as normal test lamps consume excessive voltage and may thus damage the
vehicle’s electronics.
When installing cables make sure that the connection cables are not squeezed or
damaged by sharp edges. Use rubber bushings for penetrations.
• Connect the red connection cable with the positive voltage supply (12-24 V).
This cable should be protected with an appropriate fuse in the circuit and connected to the on-
board electrical system in order to be able to turn on and off the lamp.
This switch can be, e.g. a light switch in a caravan or camper, a door contact switch if the lamp
has been built in a cabinet.
Ensure under any circumstances the sufficient dimensioning of the switch, viz. its capacity must
at least correspond with the total current consumption of all connected consumers.
The fuse value conforms to the power input of all users connected to the lead.
• Connect the black connection cable with the negative voltage supply (ground).
Maintenance and Cleaning
This lamp is maintenance-free.
Only clean it with a slightly moistened cloth. Never use cleaning agents as these can damage the
surface of the casing.
Disposal
Electronic devices are recyclables and must not be disposed of in the household
waste!
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Technical Data
Operating voltage.........................................12-24 V/DC
Power consumption.....................................2.6 W max.
Light colour ...................................................warm white (3000 K)
Beam angle ...................................................120°
Luminous flux ................................................197 lm
Illuminant .......................................................42 LEDs
Protection class ...........................................IP66
Connection cable .........................................50 cm
Dimensions....................................................130 x 11 mm (Ø x H)
Weight ............................................................85 g
Operating temperature................................-20 to +60 °C
G
Operating Instructions
LED Damp Room Light, Round
Item no. 1228766
Intended use
The LED lamp serves as light source inside vehicles.
The product is approved only for the 12 V or 24 V direct current vehicle supply system with the
negative pole of the battery at the car body, and may only be installed and used in cars with this
supply system on board. Never connect the lamp to any other voltage supply.
The product is waterproof and can also be used in outdoor areas and in damp rooms.
Use other than that described above will lead to damage to the product and will expose you to
additional risks, such as short circuits, fire, electrical shocks etc.
No part of the product may be modified or converted.
Always observe the safety instructions and all other information included in these operating in-
structions.
This product complies with the applicable national and European regulations. All company and
product names are the trademarks of their respective owners. All rights reserved.
Package contents
• LED lamp
• Assembly screws
• Operating instructions
Explanation of symbols
This symbol indicates specific risks associated with handling, function and use.
Safety Instructions
First, read the complete operating instructions carefully, as they contain important
information about proper operation of the device.
Damage due to failure to follow these operating instructions will void the warranty!
We do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions! In such cases, the warranty will
be null and void!
• Check the lamp for damage before first-time use. If the device is damaged, it must
not be put into operation.
• For safety reasons, any unauthorised conversion and/or modification to the product
is not permitted.
• The device may only be supplied with power via the 12 V or 24 V direct current vehi-
cle power supply (with the negative pole of the battery connected to the car body).
Never connect the lamp to any other voltage supply.
• If you have doubts about how the equipment should be operated or how to safely
connect it, consult a trained technician.
• Regularly check the lamp and the connection cables for damage. An expert must
repair the product in case the lamp or the connection cables are damaged.
• Avoid heavy mechanical stress on the lamp and do not expose it to high tempera-
tures, strong vibration or dripping or spray water.
• Keep the unit out of the reach of children. Keep it out of the reach of children.
• Do not leave packaging material carelessly lying around. It may become a dangerous
plaything for children.
• If in doubt about how to connect the product correctly, or should any questions arise
that are not answered in these operating instructions, please contact our technical
service or any other professional expert.
• Also observe the additional safety instructions in each individual section of these
instructions.
Installation
Modifications to the vehicle which are made necessary due to the installation of the
lamp must always be carried out in such a manner that neither the traffic safety nor the
designed stability of the car is impaired. If you are in doubt when selecting a place for
installation, consult your vehicle dealer.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2014 by Conrad Electronic SE.