background image

R0E521000EPB00 User’s Manual 

Important 

REJ10J0844-0400  Rev.4.00  October 16, 2007 

 

 

Page 4 of 88 

 

Important 

Before using this product, be sure to read this user's manual carefully. 

Keep this user’s manual, and refer to this when you have questions about this product. 

 

 

Emulator: 

The emulator in this document refers to the following products that are manufactured by Renesas Technology Corp.: 

(1) PC7501 Emulator main unit 

(2) Emulation probe 

(3) Package converter board for connecting the user system 

The emulator herein does not include the customer’s user system and host machine. 

 

 

Purpose of use of the emulator: 

This emulator is a device to support the development of a system that uses the R8C/Tiny Series Renesas 16bit single-chip 

MCUs. It provides support for system development in both software and hardware. 

Be sure to use this emulator correctly according to said purpose of use. Please avoid using this emulator for other than its 

intended purpose of use. 

 

 

For those who use this emulator: 

This emulator can only be used by those who have carefully read the user’s manual and know how to use it. 

Use of this emulator requires the basic knowledge of electric circuits, logical circuits, and MCUs. 

 

 

When using the emulator: 

(1)

 

This product is a development supporting unit for use in your program development and evaluation stages. In mass-

producing your program you have finished developing, be sure to make a judgment on your own risk that it can be put to 

practical use by performing integration test, evaluation, or some experiment else. 

(2)

 

In no event shall Renesas Solutions Corp. be liable for any consequence arising from the use of this product. 

(3)

 

Renesas Solutions Corp. strives to renovate or provide a workaround for product malfunction at some charge or without 

charge. However, this does not necessarily mean that Renesas Solutions Corp. guarantees the renovation or the provision 

under any circumstances. 

(4)

 

This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, 

it does not fall under the application of Electrical Appliance and Material Safety Law and protection against 

electromagnetic interference when used in Japan. 

(5)

 

Renesas Solutions Corp. cannot predict all possible situations or possible cases of misuse where a potential danger exists. 

Therefore, the warnings written in this user’s manual and the warning labels attached to this emulator do not necessarily 

cover all of such possible situations or cases. Please be sure to use this emulator correctly and safely on your own 

responsibility. 

(6)

 

This product is not qualified under UL or other safety standards and IEC or other industry standards. This fact must be 

taken into account when taking this product from Japan to some other country. 

Содержание R0E521000EPB00

























































































Отзывы: