Renesas R0E521000EPB00 Скачать руководство пользователя

Страница: 26 / 88

R0E521000EPB00 User’s Manual

2. Setup

REJ10J0844-0400 Rev.4.00 October 16, 2007

Page 26 of 88

2.7 Downloading Firmware

2.7.1 When It is Necessary to Download Firmware

Normally, the following are automatically detected when the emulator debugger is started up, and the firmware is downloaded.

It is necessary to download the firmware when:

(1) you use this product for the first time

(2) the firmware has been upgraded

(3) the emulator debugger has been upgraded

(4) you use this product with a PC7501 which was previously used with other emulation probe

If downloading firmware is not completed in the cases below, redownload the firmware.

- When the power is unexpectedly shut down during a download from the emulator debugger

- When a communications interface cable is unexpectedly pulled out

2.7.2 Downloading Firmware in Maintenance Mode

Download the firmware in maintenance mode as explained here following.

The user system must not be connected when

downloading the firmware.

Figure 2.5 shows the LED display on the upper panel of the PC7501 when downloading firmware

in maintenance mode.

(1) Set the interface select switch on the rear panel of the PC7501 to the LPT side and connect the LPT parallel interface cable

to the PC7501 and the host machine.

(2) Within 2 seconds of activating power to the emulator, press the RESET switch on the PC7501 front panel to switch to

maintenance mode.

Switched to maintenance mode, the SAFE SYSTEM STATUS LED begins to flash.

(3) Start up the emulator debugger. When the Init dialog box setup is complete, the dialog which urges to download the

firmware will appear. Download the firmware following messages. Required time for downloading the firmware is about

60 seconds.

Figure 2.5 Downloading firmware in maintenance mode

IMPORTANT

Note on Downloading Firmware:

Do not shut OFF power while the firmware is being downloaded. Doing so, the emulator will not start up
properly. If power is shut OFF by mistake, redownload the firmware in maintenance mode.

Downloading firmware started

Maintenance mode default

Download terminated

: ON

: OFF

POWER

SAFE

ERROR

CLOCK
RESET

RUN

WARNING

TARGET

STATUS

SYSTEM

STATUS

SYSTEM

POWER

SAFE

ERROR

CLOCK

RESET
RUN
WARNING

TARGET

STATUS

POWER

SAFE

ERROR

CLOCK

RESET
RUN

WARNING

TARGET

STATUS

SYSTEM

STATUS

POWER

SAFE

ERROR

CLOCK

RESET

RUN
WARNING

TARGET

STATUS

SYSTEM

STATUS

SYSTEM

POWER

SAFE

ERROR

CLOCK

RESET
RUN
WARNING

TARGET

STATUS

: Flashing

Содержание R0E521000EPB00

























































































Результаты поиска

Содержание R0E521000EPB00

Отзывы:

Похожие инструкции для R0E521000EPB00

Бренды по названию

Популярные бренды

Renesas R0E521000EPB00, Руководство пользователя

Результаты поиска

Содержание R0E521000EPB00

Отзывы:

Похожие инструкции для R0E521000EPB00

Бренды по названию

Популярные бренды