manualshive.com logo in svg

Renault Laguna III, Руководство пользователя

Поделиться
Скачать
Renault Laguna III Скачать руководство пользователя страница 31

01D

-

1

MECHANICAL INTRODUCTION

Vehicle: Precautions for the repair

01D

GENERAL INFORMATION

All information contained in these manuals is intended
exclusively for automotive industry professionals.

The documentation is intended to cover all vehicles in
the

 RENAULT 

range throughout the world, but may not

cover equipment designed for use in specific countries.

The  procedures  and  fault  finding  procedures  recom-
mended and described in this manual have been de-
signed by automotive industry repair professionals.

1 - General recommendations

Observe basic principles of vehicle repair.

The quality of repair depends first and foremost on the
care exercised by the person in carrying it out.

To ensure good repair:

- protect  the  sensitive  areas  of  the  vehicle  (seats,

steering wheel, wings, etc.),

- unless otherwise indicated, all repairs must be done

with the ignition off,

- when welding on the vehicle, it is advisable to remove

or disconnect components near the repair area that
could be affected by the heat,

- use recommended professional products and original

parts,

- observe the tightening torques,

- replace roll pins, self-locking or bonded nuts or bolts

every time they are removed,

- take care with electrical and electronic components

which cannot withstand excess voltage and improper
handling; replace any electrical and electronic com-
ponents which have experienced a voltage drop,

- make sure that the connectors are correctly clipped,

- do not pull on the wiring,

- check for the sealing plugs on the connectors,

- Do not splash any liquid, regardless of its type (oil,

cleaner, etc.), on the electric and electronic compo-
nents (computers, sensors, etc.)

- do not just replace parts one after the other, carry out

detailed fault finding beforehand,

- carry out a final check before returning the vehicle to

the customer (set the clock, check the alarm opera-
tion, check the lights and indicators etc.),

- clean  and  degrease  the  sections  to  be  bonded

(threads, stub axle splines) to ensure proper adher-
ence,

- protect the accessories and timing belts, the electrical

accessories  (starter,  blanking  cover,  electric  power
assisted steering pump) and the mating face to pre-
vent diesel fuel spilling onto the clutch friction plate.

The design quality of our vehicles demands that noth-
ing is left to chance in making a good repair, and it is
essential to refit parts or components exactly as they
were originally (for instance: heat shields, wiring rout-
ing, pipe routing, particularly in the area of the exhaust
pipe).

Do not blow away asbestos particles or dust (brakes,
clutch, etc.), vacuum them up or clean the component
with a cleaning agent (such as a brake cleaning prod-
uct).

Use professional products and apply them with care,
for example do not apply too much sealing paste to the
sealing surface.

Exhaust gases (petrol and diesel) are pollutants. Oper-
ate engines with care and always use exhaust gas ex-
tractors.

Ensure that there is no risk of a short circuit occurring
when the electrical connections are reconnected (e.g.
starter, alternator, etc.). Some points need greasing,
others do not, therefore particular attention should be
paid during refitting operations to ensure that they work
properly under all conditions.

2 - Special tooling - ease of use

The repair procedures have been designed using spe-
cial  tools;  they  must  therefore  be  carried  out  using
these tools to ensure a high degree of working safety
and quality of repair.

The  equipment  we  have  approved  has  undergone
careful  research  and  testing,  and  must  be  used  and
maintained with care.

3 - Reliability - updating

New repair procedures are constantly being developed
in the interests of repair quality, either with new prod-
ucts (emission control, injection, electronics, etc.), or in
fault finding. Be sure to consult the Workshop Repair
Manuals or Technical Notes or fault finding summaries
before any servicing operation.

Since vehicle specifications are subject to change dur-
ing their commercial life, it is essential to check wheth-
er  there  are  any  updated  Technical  Notes  when
seeking information.

Содержание Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды