manualshive.com logo in svg

Renault Laguna III, Руководство пользователя

Поделиться
Скачать
Renault Laguna III Скачать руководство пользователя страница 1034

13B

-

95

DIESEL INJECTION

Fuel pressure regulator: Removal - Refitting

M9R, and 744 or 748 or 754 or 800 or 802 or 805 or 806 or 808 or 809 or 816 or 845 or 849

13B

a

a

Remove:

- the bolts (

2

) from the fuel pressure regulator,

- fuel pressure regulator.

a

Insert the blanking plugs.

REFITTING

I - REFITTING PREPARATION OPERATION

a

Always replace the fuel pressure regulator seal.

a

Use

  SURFACE  CLEANER 

  (see 

Vehicle:  Parts

and consumables for the repair

) (04B, Consum-

ables - Products) to clean the bearing faces of the
fuel pressure regulator.

a

Wipe the bearing face of the fuel pressure regulator
on the high pressure pump using a

 compressed air

nozzle

 (see 

13B

, 

Diesel  injection

, 

Diesel  injec-

tion: Precautions for the repair

, page 

13B-1

) .

a

Remove:

- the blanking plug from the fuel pressure regulator,

- the fuel pressure regulator seal.

a

Refit the new fuel pressure regulator seal.

a

Lubricate the fuel pressure regulator seal.

a

Remove  the  blanking  plug  on  the  high  pressure
pump.

a

Flush the fuel pressure regulator housing by activat-
ing the manual priming pump.

II - REFITTING OPERATION FOR PART 
CONCERNED

a

Refit:

- the fuel pressure regulator, rotating it slightly in a

clockwise  direction  while  pushing  it  gently  down
until fully engaged,

- the fuel pressure regulator bolts.

a

Torque tighten the

 fuel pressure regulator bolts (6

N.m)

.

a

Connect the fuel pressure regulator connector.

III - FINAL OPERATION

a

Refit the air filter box air outlet pipe.

a

Tighten the air filter box air outlet pipe clip on the tur-
bocharger side.

a

Clip:

- the turbocharging pressure regulator control pipe

onto the air filter box air outlet pipe,

- the  air  flowmeter  wiring  onto  the  air  filter  box  air

outlet pipe,

a

Refit:

- the air filter unit (see 

12A

, 

Fuel mixture

, 

Air filter

unit: Removal - Refitting

, page 

12A-13

) ,

- the engine cover.

a

Connect the battery (see 

Battery: Removal - Refit-

ting

) (80A, Battery).

124533

WARNING

To  avoid  any  corrosion  or  damage,  protect  the
areas on which fuel is likely to run.

WARNING

To  prevent  impurities  from  entering  the  circuit,
place  protective  plugs  on  all  fuel  circuit  compo-
nents exposed to the open air.

Содержание Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды