REMKO ML 263 DC Скачать руководство пользователя страница 50

Страница: 50 / 64

Fault EC: No cooling performance or heating performance after 30 minutes

Switch the unit off for 5 seconds. Is the fault still

shown on the display?

YES

Is the indoor unit blowing out cold air or warm

air?

YES

Check the probe on the evaporator (T2). Is this

correctly seated?

YES

Check all pipe connections for leak-tightness. Is

there a deficit of refrigerant?

Replace the indoor unit circuit board.

YES

Rectify the leak and fill with new refrigerant.

Are the pipelines kinked or perhaps contami-

nated?

YES

Replace the pipelines.

Fault P0: Inverter module fault

Check the electrical wiring between the circuit

board and the compressor. Is this correctly

implemented?

Replace the connections.

YES

Check whether the IPM module is correctly

installed.

Correct the installation and retighten all

screwed connections.

YES

Does the condenser fan run properly?

Check the connection of the condenser fan

motor or replace it if necessary.

YES

Replace the outdoor unit motherboard. Is the

fault still present?

YES

Replace the compressor.

REMKO ML...DC

Содержание ML 263 DC

































































Результаты поиска

Содержание ML 263 DC

Отзывы:

Похожие инструкции для ML 263 DC

Бренды по названию

Популярные бренды

REMKO ML 263 DC, Руководство по сборке и эксплуатации

Результаты поиска

Содержание ML 263 DC

Отзывы:

Похожие инструкции для ML 263 DC

Бренды по названию

Популярные бренды