background image

 

4  

RELM 

Communications, 

Inc. 

User Safety, Training, and General Information 

READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION 
BEFORE USING YOUR RELM HANDHELD PORTABLE TWO-WAY RADIO. 

Compliance with RF Energy Exposure Standards 

Your 

RELM

 two-way radio is designed and tested to comply with a number of national and 

international standards and guidelines (listed below) regarding human exposure to radio 
frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP 
exposure limits for occupational/controlled RF exposure environment at duty cycles of up to 
50% talk-50% listen and should be used for occupational use only. In terms of measuring RF 
energy for compliance with the FCC exposure guidelines, your radio radiates measurable RF 
energy only while it is transmitting (during talking), not when it is receiving (listening) or in 
standby mode. 

Note:

 The approved batteries supplied with this radio are rated for a 5-5-90 duty cycle (5% 

talk-5% listen-90% standby), even though this radio complies with the FCC occupational 
RF exposure limits at duty cycles of up to 50% talk. 

 
Your RELM two-way radio complies with the following RF energy exposure 
standards and guidelines:

 

  United States Federal Communications Commission, Code of Federal Regulations; 47CFR 

part 2 sub-part J 

  American National Standards Institute (ANS)/Institute of Electrical and Electronic Engineers 

(IEEE) C95. 1-1992

 

  Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition 

•  

International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 

• 

Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radio frequency 
Electromagnetic Fields in the Frequency Range from 3kHz to 300GHz, 1999 

  Australian Communications Authority Radio communications (Electromagnetic 

Radiation-Human Exposure) Standard 1999 (applicable to wireless phones only)

 

Operational Instructions and Training Guidelines 

To ensure optimal performance and compliance with the occupational/controlled environment 
RF energy exposure limits in the above standards and guidelines, users should transmit no more 
than 50% of the time and always adhere to the following procedures: 

Transmit and Receive 

To transmit (talk), push the Push-To-Talk (PTT) button; to receive, release the PTT button. 

Hand-held radio operation 

Hold the radio in a vertical position with the microphone one to two inches (2.5 to 5 cm) away 
from the lips. 

Body-worn operation 

  Always place the radio in a RELM approved clip, holder, holster, case, or body harness for 

this product. Use of non-RELM-approved accessories may exceed FCC RF exposure 

Содержание RPV599A






















Отзывы: