RELM RMV8125 Скачать руководство пользователя страница 12

Страница: 12 / 14

9.3 Edit Scan List

9.4 Add or Delete the Channels in the Scan List

A. Press the

“

Menu Selection/Enter

”

button to enter the menu

mode.

B. Press / button until

“

PROG LST

”

C. Press button to select

“

SCAN LIST

”

D. Press / button until

“

ADD LST?

”

“

DEL LST?

”

E. Press button for selection.

F. Press / button until the channel you want to add or delete.

G. Press button to complete operation you will see

“

CHN

SAVE

”

(If you added a channel)or

“

CHN DEL

”

H. Press button to return to the previous operation.

9.5 Set Priority Channel

①

. Press the

“

Menu Selection/Enter

”

button to enter the menu

mode.

②

. Press / button until

“

PROG LST

”

③

. Press button to select

“

SCAN LIST

”

④

. Press / button until

“

ED PRIO?

”

⑤

. Press button for selection.

⑥

. Press / button until

“

PRIO#1?

”

“

PRIO#2?

”

⑦

. Press button to select the type of the required priority channel.

For example, in Step 7, the type of priority channel is

“

DES?

”

Press / button to select the required priority channel.

⑧

. Press button to complete operation.

10. OST

In a certain specific channel, you can revise the CTCSS/DCS

encode/decode setup of current channel.

The operating steps go as follows:

A.Press the

“

OST

”

button to enter the OST menu mode.

⑨

. Press button to return to the previous operation.

B. Press / button until the CTCSS/DCS encode/decode you

want.

C. Press button to select .

Note:

When the OST backup function is enabled, the radio retains

the OST code of each channel even if the channel is changed

or the radio is shut down.

In the OST state, P2

“·”

icon will display.

Press

“

OST

”

button again to return to normal operation.

11. Wired Clone Mode

If the wired clone function is enabled, the radio will not quit after

entering the wired clone mode. To return to normal user mode, the user

needs to restart the machine.

The operating steps go as follows:

①

. Press and buttons for power-on until show

“

CLONE

”

(for two seconds) and enter the clone mode. If the function is disabled,

Содержание RMV8125















Результаты поиска

Содержание RMV8125

Отзывы:

Бренды по названию

Популярные бренды

RELM RMV8125, Инструкция по эксплуатации

Результаты поиска

Содержание RMV8125

Отзывы:

Бренды по названию

Популярные бренды