Reliance HS 7000, Инструкция по установке и эксплуатации, Руководство пользователя, Страница: 15 / 48

IN-7000
15
4.5. Home Feature
4.5.1 The Home Feature allows the user to program the
distance the chair lift will travel when starting from the fully
lowered position. Activating this Feature causes the chair to
move upward for a fixed amount of time. The actual height
achieved by the chair will vary slightly from the programmed
height, depending on the weight of the patient.
4.5.2 The Home Feature can be initiated by any of the
RAISE BASE switches, located on the chair back, footswitch,
or instrument stand. Each switch can be independently
programmed for a specified height.
4.5.3 To PROGRAM the Home Mode Feature.
4.5.3.1 The chair lift must be fully lowered. To make sure the
lift is all the way down, DEPRESS the AUTO switch and wait
at least fifteen seconds.
4.5.3.2 The RAISE BASE switches that are to be programmed
for Home Mode, must be in Momentary Mode.
4.5.3.3 DEPRESS and HOLD either STOP switch located on
the chair back.
4.5.3.4 With the stop switch depressed, DEPRESS the RAISE
BASE switch to be programmed. The chair lift will begin to
rise and the LED’s will blink. Release both switches.
4.5.3.5 When the chair rises to the desired height, DEPRESS
either STOP switch to program that height into the chair.
4.5.3.6 Repeat steps 1 thru 5 to program any other RAISE
BASE switch for Home Mode.
4.5.4 To UTILIZE the Home Mode Feature.
4.5.4.1 When the chair is all the way down, depressing a Raise
Base Switch that has been programmed for Home Mode will
cause the chair to rise to the programmed height.
4.5.4.2 If a RAISE BASE switch is programmed for Home
Mode, but the chair lift is not all the way down, the Raise Base
switch will function like a momentary switch.
4.5.4.3 If any RAISE BASE switch is programmed for Home
Mode, the LED’s will blink for 15 seconds after the AUTO
DOWN switch is depressed. When the LED’s stop blinking,
the chair lift is all the way down.
4.5.5 To EXIT the Home Mode Feature.
4.5.5.1 If the Home Feature is no longer needed for any of
the RAISE BASE switches, depress a STOP switch and the
desired RAISE BASE switch at any time when the chair lift is
not all the way down.
NOTE:
The Home Feature and Memory Feature can
only be operated with the Base down and the Back
fully upright See Section 3.5.2 Step 4
REMARQUE
: La fonctionnalité Accueil et la
fonctionnalité Mémoire peuvent être utilisées
seulement lorsque la base est en bas et que
l’arrière est entièrement relevé. Consultez la
Section 3.5.2 Étape 4.
5.0 LOCATING AND REPLACING FUSES
WARNING: DISCONNECT EQUIPMENT
FROM MAIN INPUT POWER BEFORE
P R O C E E D I N G W I T H E L E C T R I C A L
INSPECTIONS OR MAINTENANCE.
AVERTISSEMENT : DÉCONNECTEZ
L’ÉQUIPEMENT DE L’ALIMENTATION
ÉLECTRIQUE PRINCIPALE AVANT
DE PROCÉDER À DES INSPECTIONS
ÉLECTRIQUES OU À DE L’ENTRETIEN.
CAUTION
: Replace fuse(s) as marked. All
fuses must be replaced with a fuse of the same
size and rating. Refer to the Wire Diagrams
at the end of this Manual.
PRÉCAUTION
: Remplacez le(s) fusible(s)
comme indiqué. Tous les fusibles doivent
être remplacés par un fusible de la même
dimension et de la même valeur. Se référer
aux schémas de câblage à la fin de ce manuel.
The chair contain two fuses located inside the AC Input
Module in the Base Assembly.
5.1. Fuse Replacement (AC Input Module)
5.1.1. Unplug the power cord from the AC power input
module. Referring to Figure 7, locate tab. With a tool similar
to a small common screwdriver placed under tab, pry fuse
drawer out. Remove the drawer by pulling it out with your
fingers.
