REHM BARRACUDA 105i Скачать руководство пользователя страница 4

Страница: 4 / 36

Safety

Glossary of symbols

☞

provides further instructions

➜

calls on you to act



listings

This part of the operating instructions



explains the meaning and use of the warning notes included in these operating instructions,



defines the intended use of the welding machine,



points out the dangers that might arise for you or others if these instructions are not observed,



informs you about how to avoid dangers.

In addition to these operation instructions, please observe



the applicable laws and regulations,



the statutory provisions for accident prevention,



the prohibition, warning and mandatory signs as well as the warning notes on the welding machine.

Always keep this documentation close to the welding machine.

1.1 Safety

instructions

(warning

notes)

Classification of hazards

We classify the safety warnings into different categories. The table below gives an overview of the classification
of symbols (ideogram) and the warning signs for each specific danger and its (possible) consequences.

Symbol

Alarm expression

Definition / consequence

DANGER!

Impending danger that will cause serious injury or death to people.

WARNING!

A danger that can cause serious injury or death.

CAUTION!

A danger or unsafe procedure that can cause personal injury or damage to
property.

ATTENTION!

Situation that could cause damage to the drilling machine and product, as well
as other types of damage.
No risk of injury to persons.

Information

Practical tips and other important or useful information and notes.
No dangerous or harmful consequences for people or objects.

Содержание BARRACUDA 105i





































Результаты поиска

Содержание BARRACUDA 105i

Отзывы:

Похожие инструкции для BARRACUDA 105i

Бренды по названию

Популярные бренды

REHM BARRACUDA 105i, Руководство по эксплуатации

Результаты поиска

Содержание BARRACUDA 105i

Отзывы:

Похожие инструкции для BARRACUDA 105i

Бренды по названию

Популярные бренды