Regency ULTRAGLOOW G36D-LP Скачать руководство пользователя

Страница: 10 / 40

UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace

INSTALLATION

EXTERIOR VENT TERMINATION LOCATIONS

Fixed

Openable

Closed

Openable

ertical

ermination

ent

terminal

Area

where

terminal

not

permited

Air

supply

outlet

24"

Inside

corner

det

ail

24"

18"

ertical

ermination

Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm)

Clearance to window or door that may be opened *(12"/30cm) #(9"/23cm)

Clearance to permanently closed window *(min. 12"/30cm)

ertical clearance to ventilated sofﬁ

t located above the terminal within a horizontal

distance of (24"/60cm) from the centerline of the terminal (min. 18"/46cm) check with

local code.

Clearance to unventilated sofﬁ

(min.

15"/38cm)

Clearance to outside corner: with

AstroCap

rmination Cap (min. 6"/15cm), with

Dura-V

ent

rmination Cap (14"/36cm)

Clearance to inside corner: with

AstroCap

rmination Cap (min. 6"/15cm), with Dura-

ent

rmination Cap (12"/30cm)

Not to be installed above a meter/regulator assembly within (3'/90cm) horizontally

from the centerline of the regulator

Clearance to service regulator vent outlet *(min. 36"/90cm)

Clearance to non-mechanical air supply inlet to building or the combustion air inlet to

any other appliance *(12"/30cm) #(9"/23cm)

Clearance to a mechanical air supply inlet *(min. 72"/1.8m)

#3' (91cm) above if with in 10' (3m) horizontally

Clearance above paved sidewalk or a paved driveway located on public property

*(min. 84"/2.1m)

Clearance under veranda, porch, deck, or balcony *(min. 12"/30cm)

Note:

vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings a

nd serves both dwellings.

- Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the ﬂ

oor

- If the vent termination is accessible, a certiﬁ

ed guard shall be installed.

As speciﬁ

ed in CGA

B149 Installation Code. Note: Local codes or regulations may require dif

ferent clearances.

# In accordance with the current

ANSI Z223.1/NFP

54 ,National Fuel Gas Code.

Содержание ULTRAGLOOW G36D-LP









































Результаты поиска

Содержание ULTRAGLOOW G36D-LP

Отзывы:

Похожие инструкции для ULTRAGLOOW G36D-LP

Бренды по названию

Популярные бренды

Regency ULTRAGLOOW G36D-LP, Инструкция для владельца и по установке

Результаты поиска

Содержание ULTRAGLOOW G36D-LP

Отзывы:

Похожие инструкции для ULTRAGLOOW G36D-LP

Бренды по названию

Популярные бренды