Regency U39-LP11, Инструкция для владельца и по установке

Страница: 18 / 56

18
|
Regency ® U39-11 ULTIMATE™ Freestanding Gas Stove
installation
Outside
Wall
Mur extérieur
Furring
Strips
Fourrures en bois
Furstrp.eps
see also c34020a.eps
furstrpf.eps
french
e) Cut the 2 ft. or 4 ft. section of rigid pipe to
length. Ensure that the pipe length when
cut will seat onto both the starter collar and
the 90
o
elbow. Crimped section of rigid
pipe seats into the 90
o
elbow. Only cut
the uncrimped side of pipe.
Dismantle all pipe sections including vent
terminal.
3. Attach the 4" dia. flex liner to the vent terminal
ensuring that the flex overlaps the collar of the
vent terminal by a minimum of 1-3/8"(35mm).
Use Mill-Pac to seal and secure with 3 of the
#8 x 1/2" screws (stainless steel).
4. Attach the adjustable pipe section to the vent
terminal using Mill-Pac and attach with 3 of
the #8 x 1/2" screws (stainless steel).
Note: The pipe seam should be facing down.
Note: To make the installation more aesthetically
pleasing, we recommend framing out a
square that the cap can be mounted on.
Hint: leave an extra 12" to 16" of length, this will
make the final assembly easier to work with.
9. Secure the 4" dia. flex liner to the 4" adapter with
Mill-Pac and 3 of the #8 x 1/2" screws (stainless
steel).
10. Slide the decorative Thimble Cover over the
pipe sections and secure with 4 screws (#8 x
1-1/2" drill point, black) to the wall.
11. Slide the 90
o
elbow (crimp end up) and the 2
ft. or 4 ft. pipe section (crimp end up) over the
4" dia. flex liner.
12. Slide the trim collar over the adjustable pipe
sections to cover the joint of the telescopic
section.
13. Install the spring spacers onto the pipe sections.
14. Secure the 4" dia. flex liner with adapter onto
the stove collar. Put a bead of Mill-Pac around
the appliance adapter and secure with 3 screws
(#8 x 1/2, stainless steel).
15. Attach the pipe section onto the starter collar
by sealing with Mill-Pac and securing with 3 of
the #8 x 1/2" (black) screws. Pipe seams should
be facing the wall.
16. Attach the 90
o
elbow onto the pipe section by
sealing with Mill-Pac and securing with 3 of the
#8 x 1/2" screws (black).
17. Slide the adjustable pipe section onto the 90 o
elbow. The flex may have to be compressed back
in order for the adjustable pipe to properly mate
to the elbow. Seal with Mill-Pac and secure with
3 of the #8 x 1/2" screws (black). Pipe seams
facing down.
18. Install the trim collar over the starter collar
and secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
NOTE: For best results and optimum
performance with each approved venting
system, it is highly recommended to apply
“Mill-Pac” sealant (supplied) to every inner
pipe connection. Failure to do so may result
in drafting or performance issues not covered
under warranty.
that the termination is not recessed
into the siding. For vinyl siding standoff
installation refer to the Dura-Vent
Termination instructions.
5. Slide the partially connected
pipe and vent terminal
assembly through the wall
thimbles (from the exterior
into the interior) and secure
the cap to the exterior
wall with 4 of the supplied
screws (#8 x 1-1/2" drill
point, stainless steel). Note:
pilot holes will
need to be drilled through the wall thimble on
all 4 corners.
Note: The four screws provided for the vent
cap should be replaced with appropriate
fasteners for stucco, brick, concrete, or
other types of sidings.
6. A bead of non-hardening mastic should be run
around both the termination and vinyl siding
standoff to prevent water from entering and
to make a tight seal between the cap and the
standoff.
7. Stretch the 4" dia. flex liner out fully and get a
trial fit of the liner onto the 4" dia. starter collar.
8. Cut the 4" dia. flex liner to the desired size.
Note: If installing termination on a siding
covered wall, a vinyl siding standoff or
furring strips must be used to ensure