manualshive.com logo in svg

Regency Plateau PTO30-LP, Инструкция для владельца и по установке, Страница: 18 / 32

Поделиться
Скачать
Regency Plateau PTO30-LP Скачать руководство пользователя страница 18

18

Regency Plateau™ PTO30 Outdoor Gas Fireplace

End Caps

INSTALLATION

Before installation,stainless steel must be handled and cleaned as per instructions noted below:

Stainless Steel Table Top

• Stainless table top must be inspected for scratches and dimples prior to installation.  All claims to be recorded at this time.  
Claims for damage after installation will not receive consideration.

• 

To protect the fi nish during installation and handling

 - cotton gloves 

MUST

 be worn at all times while handling the panels (even when 

removing protective coating).

•Stainless table top will discolor a little during normal operation.  
 This is normal and should not be considered a defect.

* 

All hand and fi nger marks 

MUST

 be cleaned off with a soft cloth and a stainless steel cleaner.  Most stainless steel cleaners leave a fi lm/

residue on the surface of the panels.  Use an ammonia based cleaner (ie. glass cleaner) to remove this fi lm before applying heat to the unit.

Failure to do this will result in burn stains on table top which you will be unable to remove.

  

Not protected by product warranty.

PTO30 TABLE TOP INSTALLATION

NOTE

:  These instructions apply to both the stainless steel and sunset 

bronze table tops.

Note:

 Instructions below shown with the Plateau Series coffee table base.

1)

 Place table top over completed unit.

2)

 Place end caps over pilot and opposite end to complete installation.

3)

 To remove - reverse steps.

Final Install

Содержание Plateau PTO30-LP

































Отзывы:

Нет отзывов