Regency PG36LPG5-R Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 48

background image

Regency

®

PG36-5 Gas Log Fireplace

25

PREMIUM FLUSH FRONT INSTALLATION

918-637a

08/16/07

1

PG36 / PG36D

1)

Unplug the power source.

2)

Remove the top louver (if fi tted) by carefully pulling it out.

3)

Install the premium fl ush front top louver in place by sliding the louver

tabs into the louver brackets on the inside top of the fi rebox.

Louver Tab

PREMIUM FLUSH FRONT INSTALLATION

4)

Open the bottom louver.

5)

Remove the manual control switch bracket from the bottom louver

(if fi tted) by undoing the 2 screws.

Premium Flush Front Top Louver in place.

Manual Control

Switch Bracket

6)

Remove the bottom louver (if fi tted) by undoing the 2 screws which

secure the louver to the hinges on the left and right side.

7)

Remove the heat shield by undoing the 2 screws.

8)

Carefully disconnect the reset switch wires.

9)

Lift the module off of the velcro from the base of the fi rebox and pull

out slightly.

10)

Disconnect the wire harness on the module that is connected to the

valve.

INSTALLATION

«
...
23
24
25
26
27
...
»

Содержание PG36LPG5-R

















































Отзывы:

Нет отзывов

Похожие инструкции для PG36LPG5-R

Бренд: HAMPTON BAY Страницы: 9

emifocus hublot dv

Бренд: Focus Страницы: 8

Бренд: Klarstein Страницы: 76

Бренд: Calflame Страницы: 32

Бренд: Majestic Страницы: 75

Бренд: Bali Страницы: 16

Бренд: UC Living Страницы: 28

Бренд: SEI Страницы: 8

Бренд: Valor Страницы: 80

Бренд: Valor Страницы: 45

Relaxed M Smart

Бренд: Faber Страницы: 30

Бренд: Somogyi Страницы: 18

Melrose Dark Cherry

Бренд: Stonegate Страницы: 17

Бренд: Laminvale Страницы: 9

Бренд: Valor Страницы: 12

PORTRAIT 922ECN

Бренд: Valor Страницы: 19

Бренд: Valor Страницы: 21

Бренд: Valor Fires Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды