Regency P36E-LP4 Скачать руководство пользователя страница 14

Страница: 14 / 72

P36E-4 Zero Clearance Direct Vent Gas Fireplace

TRIPOLI SCREEN DOOR COMBUSTIBLE MANTEL CLEARANCES

Because of the extreme heat this

replace emits, the mantel clearances are critical.

Combustible mantel clearances from top of unit are shown in the diagram below.

Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible

board.

These drawings are to scale at 1:6 (one inch = 6 inches)
Mantel can be installed anywhere in shaded area or higher using
the above scale.

Note: Ensure the paint that is used on the mantel and the

facing is "heat resistant" or the paint may discolour.

These drawings are to scale at 1:6 (one inch = 6 inches)
Mantel can be installed anywhere in shaded area or higher using
the above scale.

Note: Ensure the paint that is used on the mantel and the

facing is "heat resistant" or the paint may discolour.

HAMPTON

COMBUSTIBLE MANTEL CLEARANCES

Mantel Clearances with

ampton Cast Faceplate

Because of the extreme heat this

replace emits, the mantel clearances are critical.

Combustible mantel clearances from top of unit are shown in the diagram below.

Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible

board.

INSTALLATION

Содержание P36E-LP4









































































Результаты поиска

Содержание P36E-LP4

Отзывы:

Похожие инструкции для P36E-LP4

Бренды по названию

Популярные бренды

Regency P36E-LP4, Инструкция для владельца и по установке

Результаты поиска

Содержание P36E-LP4

Отзывы:

Похожие инструкции для P36E-LP4

Бренды по названию

Популярные бренды