Regency P33-LP3 Скачать руководство пользователя страница 1

Страница: 1 / 48

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

918-262a

MODELS: P33-NG3 Natural Gas P33-LP3 Propane

P33-3 Zero Clearance

Direct Vent Gas Fireplace

01/04/06

Owners &

Installation Manual

WARNING:
If the information in these instructions are not followed exactly,
a ﬁ re or explosion may result causing property damage,
personal injury or loss of life.

FOR YOUR SAFETY
Do not store or use gasoline or other ﬂ ammable vapors and
liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualiﬁ ed
installer, service agency or the gas supplier.

FOR YOUR SAFETY
What to do if you smell gas:

Do not try to light any appliance

Do not touch any electrical switch:
do not use any phone in your
building.

Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.

If you cannot reach your gas
supplier, call the ﬁ re department.

Tested by:

Installer

: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner:

Please keep these instructions for future reference.

www.regency-ﬁ re.com

Содержание P33-LP3

















































Результаты поиска

Содержание P33-LP3

Отзывы:

Похожие инструкции для P33-LP3

Бренды по названию

Популярные бренды

Regency P33-LP3, Инструкция для владельца и по установке

Результаты поиска

Содержание P33-LP3

Отзывы:

Похожие инструкции для P33-LP3

Бренды по названию

Популярные бренды